 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PRELIMINARY DATA SHEET MICRONAS INTERMETALL MSP 34x1G Multistandard Sound Processor Family with Virtual Dolby Surround Edition Oct. 15, 1999 6251-511-1PD MSP 34x1G Contents Page 6 7 7 8 9 10 10 10 10 11 11 11 13 13 13 13 13 13 14 14 14 14 14 15 15 15 15 16 16 16 17 17 17 18 19 20 20 20 20 20 21 21 21 25 26 Section 1. 1.1. 1.2. 1.3. 2. 2.1. 2.2. 2.2.1. 2.2.2. 2.2.3. 2.2.4. 2.3. 2.4. 2.5. 2.5.1. 2.5.2. 2.5.3. 2.5.4. 2.6. 2.6.1. 2.6.2. 2.6.3. 2.6.4. 2.7. 2.7.1. 2.7.2. 2.8. 2.9. 2.10. 2.11. 3. 3.1. 3.1.1. 3.1.2. 3.1.3. 3.1.4. 3.1.4.1. 3.1.4.2. 3.1.4.3. 3.1.4.4. 3.2. 3.3. 3.3.1. 3.3.2. 3.3.2.1. Title PRELIMINARY DATA SHEET Introduction Features of the MSP 34x1G Family and Differences to MSP 34xxD MSP 34x1G Version List MSP 34x1G Versions and their Application Fields Functional Description Architecture of the MSP 34x1G Family Sound IF Processing Analog Sound IF Input Demodulator: Standards and Features Preprocessing of Demodulator Signals Automatic Sound Select Preprocessing for SCART and I2S Input Signals Source Selection and Output Channel Matrix Audio Baseband Processing Automatic Volume Correction (AVC) Loudspeaker and Headphone Outputs Subwoofer Output Quasi-Peak Detector Virtual Surround System Application Tips Sweet Spot Clipping Loudspeaker Requirements Cabinet Requirements SCART Signal Routing SCART DSP In and SCART Out Select Stand-by Mode I2S Bus Interface ADR Bus Interface Digital Control I/O Pins and Status Change Indication Clock PLL Oscillator and Crystal Specifications Control Interface I2C Bus Interface Device and Subaddresses Description of CONTROL Register Protocol Description Proposals for General MSP 34x1G I2C Telegrams Symbols Write Telegrams Read Telegrams Examples Start-Up Sequence: Power-Up and I2C Controlling MSP 34x1G Programming Interface User Registers Overview Description of User Registers STANDARD SELECT Register 2 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Contents, continued Page 26 27 28 29 30 43 44 44 44 44 44 45 45 45 45 45 45 47 47 49 52 55 59 61 61 62 62 62 63 64 65 65 66 67 68 69 70 72 72 73 76 Section 3.3.2.2. 3.3.2.3. 3.3.2.4. 3.3.2.5. 3.3.2.6. 3.3.2.7. 3.4. 3.5. 3.5.1. 3.5.2. 3.5.3. 3.5.4. 3.5.5. 3.5.6. 3.5.7. 3.5.8. 3.5.9. 4. 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. 4.6.1. 4.6.2. 4.6.2.1. 4.6.2.2. 4.6.2.3. 4.6.2.4. 4.6.3. 4.6.3.1. 4.6.3.2. 4.6.3.3. 4.6.3.4. 4.6.3.5. 4.6.3.6. 4.6.3.7. 4.6.3.8. 4.6.3.9. 4.6.3.10. Title Refresh of STANDARD SELECT Register STANDARD RESULT Register Write Registers on I2C Subaddress 10hex Read Registers on I2C Subaddress 11hex Write Registers on I2C Subaddress 12hex Read Registers on I2C Subaddress 13hex Programming Tips Examples of Minimum Initialization Codes SCART1 Input to Loudspeaker in Stereo Sound SCART1 Input to Loudspeaker in 3D-PANORAMA Sound Noise Sequencer for 3D-PANORAMA Sound B/G-FM (A2 or NICAM) BTSC-Stereo BTSC-SAP with SAP at Loudspeaker Channel FM-Stereo Radio Automatic Standard Detection Software Flow for Interrupt driven STATUS Check Specifications Outline Dimensions Pin Connections and Short Descriptions Pin Descriptions Pin Configurations Pin Circuits Electrical Characteristics Absolute Maximum Ratings Recommended Operating Conditions (TA = 0 to 70 C) General Recommended Operating Conditions Analog Input and Output Recommendations Recommendations for Analog Sound IF Input Signal Crystal Recommendations Characteristics General Characteristics Digital Inputs, Digital Outputs Reset Input and Power-Up I2C-Bus Characteristics I2S-Bus Characteristics Analog Baseband Inputs and Outputs, AGNDC Sound IF Inputs Power Supply Rejection Analog Performance Sound Standard Dependent Characteristics MICRONAS INTERMETALL 3 MSP 34x1G Contents, continued Page 79 79 80 81 81 82 82 83 84 85 86 86 86 86 87 87 88 89 91 91 93 93 93 93 94 94 94 94 95 95 95 95 95 95 96 96 96 96 96 96 96 96 98 98 Section 5. 5.1. 5.2. 5.3. 5.4. 5.5. 5.6. 6. 6.1. 6.2. 6.3. 6.3.1. 6.3.1.1. 6.3.1.2. 6.3.2. 6.3.3. 6.3.4. 6.3.5. 6.3.6. 6.3.7. 6.4. 6.4.1. 6.4.2. 6.4.3. 6.4.4. 6.4.5. 6.4.6. 6.4.7. 6.5. 6.5.1. 6.5.2. 6.5.3. 6.5.4. 6.5.5. 6.5.6. 6.5.7. 6.6. 6.6.1. 6.6.2. 6.7. 6.7.1. 6.7.2. 6.8. 6.9. Title Appendix A: Overview of TV-Sound Standards NICAM 728 A2-Systems BTSC-Sound System Japanese FM Stereo System (EIA-J) FM Satellite Sound FM-Stereo Radio PRELIMINARY DATA SHEET Appendix B: Manual/Compatibility Mode Demodulator Write and Read Registers for Manual/Compatibility Mode DSP Write and Read Registers for Manual/Compatibility Mode Manual/Compatibility Mode: Description of Demodulator Write Registers Automatic Switching between NICAM and Analog Sound Function in Automatic Sound Select Mode Function in Manual Mode A2 Threshold Carrier-Mute Threshold Register AD_CV Register MODE_REG FIR-Parameter, Registers FIR1 and FIR2 DCO-Registers Manual/Compatibility Mode: Description of Demodulator Read Registers NICAM Mode Control/Additional Data Bits Register Additional Data Bits Register CIB Bits Register NICAM Error Rate Register PLL_CAPS Readback Register AGC_GAIN Readback Register Automatic Search Function for FM-Carrier Detection in Satellite Mode Manual/Compatibility Mode: Description of DSP Write Registers Additional Channel Matrix Modes Volume Modes of SCART1/2 Outputs FM Fixed Deemphasis FM Adaptive Deemphasis NICAM Deemphasis Identification Mode for A2 Stereo Systems FM DC Notch Manual/Compatibility Mode: Description of DSP Read Registers Stereo Detection Register for A2 Stereo Systems DC Level Register Demodulator Source Channels in Manual Mode Terrestric Sound Standards SAT Sound Standards Exclusions of Audio Baseband Features Phase Relationship of Analog Outputs 4 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Contents, continued Page 99 100 102 Section 7. 8. 9. Title Appendix D: MSP 34x1G Version History Appendix E: Application Circuit Data Sheet History License Notice: 1) "Dolby", "Virtual Dolby Surround", and the double-D Symbol are trademarks of Dolby Laboratories. Supply of this implementation of Dolby Technology does not convey a license nor imply a right under any patent, or any other industrial or intellectual property right of Dolby Laboratories, to use this implementation in any finished end-user or ready-to-use final product. Companies planning to use this implementation in products must obtain a license from Dolby laboratories Licensing Corporation before designing such products. MICRONAS INTERMETALL 5 MSP 34x1G Multistandard Sound Processor Family with Virtual Dolby Surround The hardware and software description in this document is valid for the MSP 34x1G version A1 and following versions. PRELIMINARY DATA SHEET signal conforming to the standard recommended by the Broadcast Television Systems Committee (BTSC). The DBX noise reduction, or alternatively, MICRONAS Noise Reduction (MNR) is performed alignment free. Other processed standards are the Japanese FM-FM multiplex standard (EIA-J) and the FM Stereo Radio standard. Current ICs have to perform adjustment procedures in order to achieve good stereo separation for BTSC and EIA-J. The MSP 34x1G has optimum stereo performance without any adjustments. All MSP 34x1G versions are pin and software downward-compatible to the MSP 34x0D. The MSP 34x1G further simplifies controlling software. Standard selection requires a single I2C transmission only. The MSP 34x1G has built-in automatic functions: The IC is able to detect the actual sound standard automatically (Automatic Standard Detection). Furthermore, pilot levels and identification signals can be evaluated internally with subsequent switching between mono/ stereo/bilingual; no I2C interaction is necessary (Automatic Sound Selection). The ICs are produced in submicron CMOS technology. The MSP 34x1G is available in the following packages: PLCC68, PSDIP64, PSDIP52, PQFP80, and PLQFP64. 1. Introduction The MSP 34x1G family of single-chip Multistandard Sound Processors covers the sound processing of all analog TV-Standards worldwide, as well as the NICAM digital sound standards. The full TV sound processing, starting with analog sound IF signal-in, down to processed analog AF-out, is performed on a single chip. Figure 1-1 shows a simplified functional block diagram of the MSP 34x1G. The MSP 34x1G has all functions of the MSP 34x0G with the addition of a virtual surround sound feature. Surround sound can be reproduced to a certain extent with two loudspeakers. The MSP 34x1G includes our virtualizer algorithm "3D-PANORAMA" which has been approved by the Dolby1) Laboratories for compliance with the "Virtual Dolby Surround" technology. In addition, the MSP 34x1G includes our "PANORAMA" algorithm. These TV sound processing ICs include versions for processing the multichannel television sound (MTS) Sound IF1 ADC Sound IF2 Demodulator Preprocessing Loudspeaker Sound Processing DAC Loudspeaker Subwoofer Source Select I2S1 I2S2 SCART1 Headphone Sound Processing DAC Headphone Prescale I2S DAC SCART2 SCART3 SCART4 MONO SCART DSP Input Select SCART1 ADC Prescale DAC SCART Output Select SCART2 Fig. 1-1: Simplified functional block diagram of the MSP 34x1G 6 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 1.1. Features of the MSP 34x1G Family and Differences to MSP 34xxD Feature (New features not available for MSP 34xxD are shaded gray.) 3401 X X transmission X X X X X X X X X X X X X X X X X X 3411 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 3421 X X X X X X X X X X X X X X X X 3431 X X X X X X X X X X X X X X X X 3441 X X X X X X X X X X X X X X X X 3451 X X X X X X X X X X X X X X X X X X X X X X X 3D-PANORAMA virtualizer (approved by Dolby Laboratories) with noise generator PANORAMA virtualizer algorithm Standard Selection with single I2C Automatic Standard Detection of terrestrial TV standards Automatic Sound Selection (mono/stereo/bilingual), new registers MODUS, STATUS Two selectable sound IF (SIF) inputs Automatic Carrier Mute function Interrupt output programmable (indicating status change) Loudspeaker / Headphone channel with volume, balance, bass, treble, loudness AVC: Automatic Volume Correction Subwoofer output with programmable low-pass and complementary high-pass filter 5-band graphic equalizer for loudspeaker channel Spatial effect for loudspeaker channel; processing of all deemphasis filtering Four Stereo SCART (line) inputs, one Mono input; two Stereo SCART outputs Complete SCART in/out switching matrix Two I S inputs; one I S output All analog FM-Stereo A2 and satellite standards; AM-SECAM L standard Simultaneous demodulation of (very) high-deviation FM-Mono and NICAM Adaptive deemphasis for satellite (Wegener-Panda, acc. to ASTRA specification) ASTRA Digital Radio (ADR) together with DRP 3510A All NICAM standards Demodulation of the BTSC multiplex signal and the SAP channel Alignment free digital DBX noise reduction for BTSC Stereo and SAP Alignment free digital MICRONAS Noise Reduction (MNR) for BTSC Stereo and SAP BTSC stereo separation (MSP 3421/41G also EIA-J) significantly better than spec. SAP and stereo detection for BTSC system Korean FM-Stereo A2 standard Alignment-free Japanese standard EIA-J Demodulation of the FM-Radio multiplex signal 2 2 1.2. MSP 34x1G Version List Version MSP 3401G MSP 3411G MSP 3421G MSP 3431G MSP 3441G MSP 3451G Status planned planned planned planned planned available Description FM Stereo (A2) Version NICAM and FM Stereo (A2) Version NTSC Version (A2 Korea, BTSC with MICRONAS Noise Reduction (MNR), and Japanese EIA-J system) BTSC Version NTSC Version (A2 Korea, BTSC with DBX noise reduction, and Japanese EIA-J system) Global Version (all sound standards) MICRONAS INTERMETALL 7 MSP 34x1G 1.3. MSP 34x1G Versions and their Application Fields Table 1-1 provides an overview of TV sound standards that can be processed by the MSP 34x1G family. In addition, the MSP 34x1G is able to handle the terrestrial FM-Radio standard. With the MSP 34x1G, a PRELIMINARY DATA SHEET complete multimedia receiver covering all TV sound standards together with terrestrial and satellite radio sound can be built; even ASTRA Digital Radio can be processed (with a DRP 3510A coprocessor). Table 1-1: TV Stereo Sound Standards covered by the MSP 34x1G IC Family (details see Appendix A) MSP Version 3401 TVSystem B/G 5.5/5.85 L I 6.5/5.85 6.0/6.552 6.5/6.2578125 3401 3411 6.5/6.7421875 D/K 6.5/5.7421875 3451 6.5/5.85 6.5 7.02/7.2 7.38/7.56 etc. 4.5/4.724212 3421, 3441 M/N 3431 4.5 4.5 FM-Radio 10.7 FM-Stereo (A2, D/K3) FM-Mono/NICAM (D/K, NICAM) FM-Mono FM-Stereo ASTRA Digital Radio (ADR) with DRP 3510A FM-Stereo (A2) FM-FM (EIA-J) BTSC-Stereo + SAP FM-Stereo Radio SECAM-East PAL Poland China, Hungary FM-Mono/NICAM AM-Mono/NICAM FM-Mono/NICAM FM-Stereo (A2, D/K1) FM-Stereo (A2, D/K2) PAL SECAM-L PAL SECAM-East PAL Scandinavia, Spain France UK, Hong Kong Slovak. Rep. currently no broadcast Position of Sound Carrier /MHz 5.5/5.7421875 Sound Modulation FM-Stereo (A2) Color System PAL Broadcast e.g. in: Germany 3401 Satellite PAL Europe Sat. ASTRA NTSC NTSC NTSC, PAL Korea Japan USA, Argentina USA, Europe 33 34 39 MHz 4.5 9 MHz SAW Filter Tuner Sound IF Mixer Loudspeaker 1 Mono Vision Demodulator SCART1 2 Subwoofer 2 MSP 34x1G Headphone SCART Inputs Composite Video SCART2 2 2 2 SCART3 SCART4 2 SCART1 SCART2 SCART Outputs I2S1 Dolby Pro Logic Processor DPL 351xA ADR I2S2 ADR Decoder DRP 3510A Fig. 1-2: Typical MSP 34x1G application 8 MICRONAS INTERMETALL 2. Functional Description Automatic Sound Select ANA_IN1+ AGC A DEMODULATOR ANA_IN2+ D (incl. Carrier Mute) Deemphasis: 50/75 s DBX/MNR Panda1 FM/AM FM/AM Stereo or A/B Stereo or A Stereo or B Prescale Loudspeaker Channel Virtualizer AVC Bass/ Treble or Equal- I2S_DA_IN1 I2S Interface Source Select SCART DSP Input Select SC1_IN_L SC1_IN_R SC2_IN_L SC2_IN_R SC3_IN_L SC3_IN_R SC4_IN_L SC4_IN_R MONO_IN SCART Output Select MICRONAS INTERMETALL 9 PRELIMINARY DATA SHEET Loudness Complementary Highpass Spatial Effects Balance Volume D DACM_L DACM_R Lowpass Beeper Level Adjust A DACM_SUB Decoded Standards: NICAM A2 AM BTSC EIA-J SAT FM-Radio NICAM Deemphasis: J17 Prescale Noise Generator Standard and Sound Detection I2C ReadRegister Headphone Channel Volume Bass/ Treble D A DACA_L Loudness Balance DACA_R ADR-Bus Interface I2S1 Prescale I2S Channel Matrix I2S Interface I2S_DA_OUT I2S_DA_IN2 I2S Interface I2S2 QuasiPeak Channel Quasi-Peak Detector I2C ReadRegister Prescale A D SCART SCART1 Channel Matrix Volume D SCART1_L/R A Prescale SCART2 Channel Matrix Volume D SCART2_L/R A SC1_OUT_L SC1_OUT_R SC2_OUT_L SC2_OUT_R MSP 34x1G Fig. 2-1: Signal flow block diagram of the MSP 34x1G (input and output names correspond to pin names) MSP 34x1G 2.1. Architecture of the MSP 34x1G Family Fig. 2-1 on page 9 shows a simplified block diagram of the IC. The block diagram contains all features of the MSP 3451G. Other members of the MSP 34x1G family do not have the complete set of features: The demodulator handles only a subset of the standards presented in the demodulator block; NICAM processing is only possible in the MSP 3411G and MSP 3451G. PRELIMINARY DATA SHEET BTSC-Mono + SAP: Detection and FM demodulation of the aural carrier resulting in the MTS/MPX signal. Detection and evaluation of the pilot carrier, detection and FM demodulation of the SAP subcarrier. Processing of DBX noise reduction or MICRONAS Noise Reduction (MNR). Japan Stereo: Detection and FM demodulation of the aural carrier resulting in the MPX signal. Demodulation and evaluation of the identification signal and FM demodulation of the (L-R)-carrier. FM-Satellite Sound: Demodulation of one or two FM carriers. Processing of high-deviation mono or narrow bandwidth mono, stereo, or bilingual satellite sound according to the ASTRA specification. FM-Stereo-Radio: Detection and FM demodulation of the aural carrier resulting in the MPX signal. Detection and evaluation of the pilot carrier and AM demodulation of the (L-R)-carrier. The demodulator blocks of all MSP 34x1G versions have identical user interfaces. Even completely different systems like the BTSC and NICAM systems are controlled the same way. Standards are selected by means of MSP Standard Codes. Automatic processes handle standard detection and identification without controller interaction. The key features of the MSP 34x1G demodulator blocks are Standard Selection: The controlling of the demodulator is minimized: All parameters, such as tuning frequencies or filter bandwidth, are adjusted automatically by transmitting one single value to the STANDARD SELECT register. For all standards, specific MSP standard codes are defined. Automatic Standard Detection: If the TV sound standard is unknown, the MSP 34x1G can automatically detect the actual standard, switch to that standard, and respond the actual MSP standard code. Automatic Carrier Mute: To prevent noise effects or FM identification problems in the absence of an FM carrier, the MSP 34x1G offers a carrier mute feature, which is activated automatically if the TV sound standard is selected by means of the STANDARD SELECT register. If no FM carrier is available at one of the two MSP demodulator channels, the corresponding demodulator output is muted. 2.2. Sound IF Processing 2.2.1. Analog Sound IF Input The input pins ANA_IN1+, ANA_IN2+, and ANA_IN- offer the possibility to connect two different sound IF (SIF) sources to the MSP 34x1G. The analog-to-digital conversion of the preselected sound IF signal is done by an A/D-converter. An analog automatic gain circuit (AGC) allows a wide range of input levels. The highpass filters formed by the coupling capacitors at pins ANA_IN1+ and ANA_IN2+ see Section 8. "Appendix E: Application Circuit" on page 100 are sufficient in most cases to suppress video components. Some combinations of SAW filters and sound IF mixer ICs, however, show large picture components on their outputs. In this case, further filtering is recommended. 2.2.2. Demodulator: Standards and Features The MSP 34x1G is able to demodulate all TV-sound standards worldwide including the digital NICAM system. Depending on the MSP 34x1G version, the following demodulation modes can be performed: A2 Systems: Detection and demodulation of two separate FM carriers (FM1 and FM2), demodulation and evaluation of the identification signal of carrier FM2. NICAM Systems: Demodulation and decoding of the NICAM carrier, detection and demodulation of the analog (FM or AM) carrier. For D/K-NICAM, the FM carrier may have a maximum deviation of 384 kHz. Very high deviation FM-Mono: Detection and robust demodulation of one FM carrier with a maximum deviation of 540 kHz. BTSC-Stereo: Detection and FM demodulation of the aural carrier resulting in the MTS/MPX signal. Detection and evaluation of the pilot carrier, AM demodulation of the (L-R)-carrier and detection of the SAP subcarrier. Processing of DBX noise reduction or MICRONAS Noise Reduction (MNR). 10 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G - "Stereo or A" channel: Analog or digital mono sound, stereo if available. In case of bilingual broadcast, it contains language A (on left and right). - "Stereo or B" channel: Analog or digital mono sound, stereo if available. In case of bilingual broadcast, it contains language B (on left and right). Fig 2-2 shows the source channel assignment of the demodulated signals in case of manual mode. If manual mode is required, more information can be found in the section "Demodulator Source Channels in Manual Mode" on page 96. Fig 2-3 and Table 2-2 show the source channel assignment of the demodulated signals in case of Automatic Sound Select mode for all sound standards. Note: The analog primary input channel contains the signal of the mono FM/AM carrier or the L+R signal of the MPX carrier. The secondary input channel contains the signal of the 2nd FM carrier, the L-R signal of the MPX carrier, or the SAP signal. 2.2.3. Preprocessing of Demodulator Signals The NICAM signals must be processed by a deemphasis filter and adjusted in level. The analog demodulated signals must be processed by a deemphasis filter, adjusted in level, and dematrixed. The correct deemphasis filters are already selected by setting the standard in the STANDARD SELECT register. The level adjustment has to be done by means of the FM/ AM and NICAM prescale registers. The necessary dematrix function depends on the selected sound standard and the actual broadcasted sound mode (mono, stereo, or bilingual). It can be manually set by the FM Matrix Mode register or automatically set by the Automatic Sound Selection. 2.2.4. Automatic Sound Select In the Automatic Sound Select mode, the dematrix function is automatically selected based on the identification information in the STATUS register. No I2C interaction is necessary when the broadcasted sound mode changes (e.g. from mono to stereo). The demodulator supports the identification check by switching between mono compatible standards (standards that have the same FM mono carrier) automatically and non-audible. If B/G-FM or B/G-NICAM is selected, the MSP will switch between these standards. The same action is performed for the standards: D/K1-FM, D/K2-FM, and D/K-NICAM. Switching is only done in the absence of any stereo or bilingual identification. If identification is found, the MSP keeps the detected standard. In case of high bit-error rates, the MSP 34x1G automatically falls back from digital NICAM sound to analog FM or AM mono. Table 2-1 summarizes all actions that take place when Automatic Sound Select is switched on. To provide more flexibility, the Automatic Sound Select block prepares four different source channels of demodulated sound (Fig 2-3). By choosing one of the four demodulator channels, the preferred sound mode can be selected for each of the output channels (loudspeaker, headphone, etc.). This is done by means of the Source Select registers. The following source channels of demodulated sound are defined: - "FM/AM" channel: Analog mono sound, stereo if available. In case of NICAM, analog mono only (FM or AM mono). - "Stereo or A/B" channel: Analog or digital mono sound, stereo if available. In case of bilingual broadcast, it contains both languages A (left) and B (right). 2.3. Preprocessing for SCART and I2S Input Signals The SCART and I2S inputs need only be adjusted in level by means of the SCART and I2S prescale registers. primary channel secondary channel FM/AM Source Select FM-Matrix Prescale FM/AM 0 LS Ch. Matrix Output-Ch. Matrices must be set according the standard SC2 Ch. Matrix NICAM A NICAM NICAM (Stereo or A/B) 1 NICAM B Prescale Fig. 2-2: Source channel assignment of demodulated signals in Manual Mode primary channel secondary channel FM/AM FM/AM 0 LS Ch. Matrix Source Select Output-Ch. Matrices must be set once to stereo Prescale Automatic Sound Select Stereo or A/B 1 NICAM A NICAM Stereo or A 3 NICAM B Prescale Stereo or B 4 SC2 Ch. Matrix Fig. 2-3: Source channel assignment of demodulated signals in Automatic Sound Select Mode MICRONAS INTERMETALL 11 MSP 34x1G Table 2-1: Performed actions of the Automatic Sound Selection Selected TV Sound Standard B/G-FM, D/K-FM, M-Korea, and M-Japan B/G-NICAM, L-NICAM, I-NICAM, and D/K-NICAM Performed Actions PRELIMINARY DATA SHEET Evaluation of the identification signal and automatic switching to mono, stereo, or bilingual. Preparing four demodulator source channels according to Table 2-2. Identification is acquired after 500 ms. Evaluation of NICAM-C-bits and automatic switching to mono, stereo, or bilingual. Preparing four demodulator source channels according to Table 2-2. NICAM detection is acquired within 150 ms. In case of bad or no NICAM reception, the MSP switches automatically to FM/AM mono and switches back to NICAM if possible. A hysteresis prevents periodical switching. B/G-FM, B/G-NICAM or D/K1-FM, D/K2-FM, D/K3-FM, and D/K-NICAM Automatic searching for stereo/bilingual-identification in case of mono transmission. Automatic and nonaudible changes between Dual-FM and FM-NICAM standards while listening to the basic FM-Mono sound carrier. Example: If starting with B/G-FM-Stereo, there will be a periodical alternation to B/G-NICAM in the absence of FM-Stereo/Bilingual or NICAM-identification. Once an identification is detected, the MSP keeps the corresponding standard. Evaluation of the pilot signal and automatic switching to mono or stereo. Preparing four demodulator source channels according to Table 2-2. Detection of the SAP carrier. Pilot detection is acquired after 200 ms. In the absence of SAP, the MSP switches to BTSC-Stereo if available. If SAP is detected, the MSP switches automatically to SAP (see Table 2-2). BTSC-STEREO, FM Radio BTSC-SAP Table 2-2: Sound modes for the demodulator source channels with Automatic Sound Select Source Channels in Automatic Sound Select Mode Broadcasted Sound Standard M-Korea B/G-FM D/K-FM M-Japan Selected MSP Standard Code3) 02 03, 081) 04, 05, 07, 0B1) 30 Broadcasted Sound Mode FM/AM (source select: 0) Stereo or A/B (source select: 1) Stereo or A (source select: 3) Stereo or B (source select: 4) MONO STEREO BILINGUAL: Languages A and B Mono Stereo Left = A Right = B analog Mono analog Mono analog Mono analog Mono Mono Stereo Mono Stereo Left = Mono Right = SAP Left = Mono Right = SAP Mono Stereo Mono Stereo Left = A Right = B analog Mono NICAM Mono NICAM Stereo Left = NICAM A Right = NICAM B Mono Stereo Mono Stereo Left = Mono Right = SAP Left = Mono Right = SAP Mono Stereo Mono Stereo A analog Mono NICAM Mono NICAM Stereo NICAM A Mono Stereo Mono Stereo Mono Mono Mono Stereo Mono Stereo B analog Mono NICAM Mono NICAM Stereo NICAM B Mono Stereo Mono Stereo SAP SAP Mono Stereo B/G-NICAM L-NICAM I-NICAM D/K-NICAM D/K-NICAM (with high deviation FM) 08, 032) 09 0A 0B, 042), 052) 0C NICAM not available or error rate too high MONO STEREO BILINGUAL: Languages A and B 20, 21 MONO STEREO 20 BTSC 21 MONO+SAP STEREO+SAP MONO+SAP STEREO+SAP FM Radio 40 MONO STEREO 1) 2) 3) The Automatic Sound Select process will automatically switch to the mono compatible analog standard. The Automatic Sound Select process will automatically switch to the mono compatible digital standard. The MSP Standard Codes are defined in Table 3-7 on page 25. 12 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 2.4. Source Selection and Output Channel Matrix The Source Selector makes it possible to distribute all source signals (one of the demodulator source channels, SCART, or I2S input) to the desired output channels (loudspeaker, headphone, etc.). All input and output signals can be processed simultaneously. Each source channel is identified by a unique source address. For each output channel, the sound mode can be set to sound A, sound B, stereo, or mono by means of the output channel matrix. If Automatic Sound Select is on, the output channel matrix can stay fixed to stereo (transparent) for demodulated signals. output level [dBr] -12 -18 -24 -30 -24 -18 -12 -6 +6 0 input level [dBr] Fig. 2-4: Simplified AVC characteristics 2.5. Audio Baseband Processing 2.5.1. Automatic Volume Correction (AVC) Different sound sources (e.g. terrestrial channels, SAT channels, or SCART) fairly often do not have the same volume level. Advertisements during movies usually have a higher volume level than the movie itself. This results in annoying volume changes. The Automatic Volume Correction (AVC) solves this problem by equalizing the volume level. To prevent clipping, the AVC's gain decreases quickly in dynamic boost conditions. To suppress oscillation effects, the gain increases rather slowly for low level inputs. The decay time is programmable by means of the AVC register (see page 34). For input signals ranging from -24 dBr to 0 dBr, the AVC maintains a fixed output level of -18 dBr. Fig. 2-4 shows the AVC output level versus its input level. For prescale and volume registers set to 0 dB, a level of 0 dBr corresponds to full scale input/output. This is - SCART input/output 0 dBr = 2.0 Vrms - Loudspeaker and Aux output 0 dBr = 1.4 Vrms 2.5.2. Loudspeaker and Headphone Outputs The following baseband features are implemented in the loudspeaker and headphone output channels: bass/treble, loudness, balance, and volume. A square wave beeper can be added to the loudspeaker and headphone channel. The loudspeaker channel additionally performs: equalizer (not simultaneously with bass/treble), spatial effects, and a subwoofer crossover filter. 2.5.3. Subwoofer Output The subwoofer signal is created by combining the left and right channels directly behind the loudness block using the formula (L+R)/2. Due to the division by 2, the D/A converter will not be overloaded, even with full scale input signals. The subwoofer signal is filtered by a third-order low-pass with programmable corner frequency followed by a level adjustment. At the loudspeaker channels, a complementary high-pass filter can be switched on. Subwoofer and loudspeaker output use the same volume (Loudspeaker Volume Register). 2.5.4. Quasi-Peak Detector The quasi-peak readout register can be used to read out the quasi-peak level of any input source. The feature is based on following filter time constants: attack time: 1.3 ms decay time: 37 ms MICRONAS INTERMETALL 13 MSP 34x1G 2.6. Virtual Surround System Application Tips 2.6.1. Sweet Spot Good results are only obtained in a rather close area along the middle axis between the two loudspeakers: the sweet spot. Moving away from this position degrades the effect. PRELIMINARY DATA SHEET 2.6.3. Loudspeaker Requirements The loudspeakers used and their positioning inside the TV set will greatly influence the performance of the virtualizer. The algorithm works with the direct sound path. Reflected sound waves reduce the effect. So it's most important to have as much direct sound as possible, compared to indirect sound. To obtain the approval for a TV set, Dolby Laboratories require mounting the loudspeakers in front of the set. Loudspeakers radiating to the side of the TV set will not produce convincing effects. Good directionality of the loudspeakers towards the listener is optimal. The virtualizer was specially developed for implementation in TV sets. Even for rather small stereo TV's, sufficient sound effects can be obtained. For small sets, the loudspeaker placement should be to the side of the CRT; for large screen sets (or 16:9 sets), mounting the loudspeakers below the CRT is acceptable (large separation is preferred, low frequency speakers should be outmost to avoid cancellation effects). Using external loudspeakers with a large stereo base will not create optimal effects. The loudspeakers should be able to reproduce a wide frequency range. The most important frequency range starts from 160 Hz and ranges up to 5 kHz. Great care has to be taken with systems that use one common subwoofer: A single loudspeaker cannot reproduce virtual sound locations. The crossover frequency must be lower than 120 Hz. 2.6.2. Clipping For the test at Dolby Labs, it is very important to have no clipping effects even with worst case signals. That is, 2 Vrms input signal may not clip. The SCART Input Prescale register has to be set to values of 19hex (25dec) or lower (see SCART Input Prescale on page 31). Test signals: sine sweep with 2 VRMS; L only, R only, L&R equal phase, L&R anti phase. Listening tests: Dolby Trailers (train trailer, city trailer, canyon trailer...) 2.6.4. Cabinet Requirements During listening tests at Dolby Laboratories, no resonances in the cabinet should occur. Good material to check for resonances are the Dolby Trailers or other dynamic sound tracks. 14 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 2.8. I2S Bus Interface It is possible to route in an external coprocessor for special effects, like surround processing and sound field processing. Routing can be done with each input source and output channel via the I2S inputs and outputs. Two possible interface formats are supported: 1. The SONY format: I2S_WS changes at the word boundaries. 2. The PHILIPS format: I2S_WS changes one I2S_CL period before the word boundaries. The I2S bus interface consists of five pins: 1. I2S_DA_IN1, I2S_DA_IN2: For input, four channels (two channels per line, 2*16 bits) per sampling cycle (32 kHz) are transmitted. 2. I2S_DA_OUT: For output, two channels (2*16 bits) per sampling cycle (32 kHz) are transmitted. 3. I2S_CL: Gives the timing for the transmission of I2S serial data (1.024 MHz). 4. I2S_WS: The I2S_WS word strobe line defines the left and right sample. The MSP 34x1G normally serves as the master on the I2S interface. In this case, the clock and word strobe lines are driven by the MSP 34x1G. In slave mode, these lines are input to the MSP 34x1G and the master clock is synchronized to 576 times the I2S_WS rate (32 kHz). NICAM operation is not possible in this mode. All I2S options can be set by means of the MODUS register (see page 28). A precise I2S timing diagram is shown in Fig. 4-26 on page 70. 2.7. SCART Signal Routing 2.7.1. SCART DSP In and SCART Out Select The SCART DSP Input Select and SCART Output Select blocks include full matrix switching facilities. To design a TV set with four pairs of SCART-inputs and two pairs of SCART-outputs, no external switching hardware is required. The switches are controlled by the ACB user register (see page 40). 2.7.2. Stand-by Mode If the MSP 34x1G is switched off by first pulling STANDBYQ low and then (after >1 s delay) switching off the 5-V, but keeping the 8-V power supply (`Standby'-mode), the SCART switches maintain their position and function. This allows the copying from selected SCART-inputs to SCART-outputs in the TV set's stand-by mode. In case of power on or starting from stand-by (switching on the 5-V supply, RESETQ going high 2 ms later), all internal registers except the ACB register (page 40) are reset to the default configuration (see Table 3-5 on page 22). The reset position of the ACB register becomes active after the first I2C transmission into the Baseband Processing part (subaddress 12hex). By transmitting the ACB register first, the reset state can be redefined. MICRONAS INTERMETALL 15 MSP 34x1G 2.9. ADR Bus Interface For the ASTRA Digital Radio System (ADR), the MSP 3401G, MSP 3411G and MSP 3451G performs preprocessing such as carrier selection and filtering. Via the 3-line ADR-bus, the resulting signals are transferred to the DRP 3510A coprocessor, where the source decoding is performed. To be prepared for an upgrade to ADR with an additional DRP board, the following lines of MSP 34x1G should be provided on a feature connector: - AUD_CL_OUT - I2S_DA_IN1 or I2S_DA_IN2 - I2S_DA_OUT - I2S_WS - I2S_CL - ADR_CL, ADR_WS, ADR_DA For more details, please refer to the DRP 3510A data sheet. PRELIMINARY DATA SHEET 2.11. Clock PLL Oscillator and Crystal Specifications The MSP 34x1G derives all internal system clocks from the 18.432-MHz oscillator. In NICAM or in I2SSlave mode, the clock is phase-locked to the corresponding source. Therefore, it is not possible to use NICAM and I2S-Slave mode at the same time. For proper performance, the MSP clock oscillator requires a 18.432-MHz crystal. Note that for the phase-locked modes (NICAM, I2S-Slave), crystals with tighter tolerance are required. Remark on using the crystal: External capacitors at each crystal pin to ground are required. They are necessary for tuning the open-loop frequency of the internal PLL and for stabilizing the frequency in closed-loop operation. The higher the capacitors, the lower the resulting clock frequency. The nominal free running frequency should match 18.432 MHz as closely as possible. Clock measurements should be done at pin AUD_CL_OUT. This pin must be activated for this purpose (see Table 3-9 on page 28). 2.10.Digital Control I/O Pins and Status Change Indication The static level of the digital input/output pins D_CTR_I/O_0/1 is switchable between HIGH and LOW via the I2C-bus by means of the ACB register (see page 40). This enables the controlling of external hardware switches or other devices via I2C-bus. The digital input/output pins can be set to high impedance by means of the MODUS register (see page 28). In this mode, the pins can be used as input. The current state can be read out of the STATUS register (see page 29). Optionally, the pin D_CTR_I/O_1 can be used as an interrupt request signal to the controller, indicating any changes in the read register STATUS. This makes polling unnecessary, I2C bus interactions are reduced to a minimum (see STATUS register on page 29 and MODUS register on page 28). 16 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G performed some other function (for example, servicing an internal interrupt), it will hold the clock line I2C_CL LOW to force the transmitter into a wait state. The positions within a transmission where this may happen are indicated by 'Wait' in section 3.1.3. The maximum wait period of the MSP during normal operation mode is less than 1 ms. 3. Control Interface 3.1. I2C Bus Interface 3.1.1. Device and Subaddresses The MSP 34x1G is controlled via the I2C bus slave interface. The IC is selected by transmitting one of the MSP 34x1G device addresses. In order to allow up to three MSP ICs to be connected to a single bus, an address select pin (ADR_SEL) has been implemented. With ADR_SEL pulled to high, low, or left open, the MSP 34x1G responds to different device addresses. A device address pair is defined as a write address (80, 84, or 88 hex) and a read address (81, 85, or 89 hex) (see Table 3-1). Writing is done by sending the device write address, followed by the subaddress byte, two address bytes, and two data bytes. Reading is done by sending the write device address, followed by the subaddress byte and two address bytes. Without sending a stop condition, reading of the addressed data is completed by sending the device read address (81, 85, or 89 hex) and reading two bytes of data. Refer to section 3.1.3. for the I2C bus protocol and to section "Programming Tips" on page 44 for proposals of MSP 34x1G I2C telegrams. See Table 3-2 for a list of available subaddresses. Besides the possibility of hardware reset, the MSP can also be reset by means of the RESET bit in the CONTROL register by the controller via I2C bus. Due to the internal architecture of the MSP 34x1G, the IC cannot react immediately to an I2C request. The typical response time is about 0.3 ms. If the MSP cannot accept another complete byte of data until it has Internal hardware error handling: In case of any internal hardware error (e.g. interruption of the power supply of the MSP), the MSP's wait period is extended to 1.8 ms. After this time period elapses, the MSP releases data and clock lines. Indication and solving of the error status: 1. MSP 34x1G-versions until A1: To indicate the error status, all further acknowledge bits will be left high. The MSP can then be reset by transmitting the reset condition to CONTROL while ignoring the missing acknowledge bits. 2. MSP 34x1G-versions from A2 on: To indicate the error status, the remaining acknowledge bits of the actual I2C-protocol will be left high. Additionally, bit[14] of CONTROL is set to one. The MSP can then be reset via the I2C bus by transmitting the reset condition to CONTROL. Indication of reset (only versions from A2 on): Any reset, even caused by an unstable reset line etc., is indicated in bit[15] of CONTROL. A general timing diagram of the I2C bus is shown in Fig. 4-25 on page 68. MICRONAS INTERMETALL 17 MSP 34x1G Table 3-1: I2C Bus Device Addresses ADR_SEL Mode MSP device address Write 80 hex Low Read 81 hex Write 84 hex High Read 85 hex PRELIMINARY DATA SHEET Left Open Write 88 hex Read 89 hex Table 3-2: I2C Bus Subaddresses Name CONTROL TEST WR_DEM RD_DEM WR_DSP RD_DSP Binary Value 0000 0000 0000 0001 0001 0000 0001 0001 0001 0010 0001 0011 Hex Value 00 01 10 11 12 13 Mode Read/Write Write Write Write Write Write Function Write: Software reset of MSP (see Table 3-3) Read: Hardware error status of MSP only for internal use write address demodulator read address demodulator write address DSP read address DSP 3.1.2. Description of CONTROL Register Table 3-3: CONTROL as a Write Register Name CONTROL Subaddress 00 hex Bit[15] (MSB) 1 : RESET 0 : normal Bits[14:0] 0 Table 3-4: CONTROL as a Read Register (only MSP 34x1G-versions from A2 on) Name CONTROL Subaddress 00 hex Bit[15] (MSB) Reset status after last reading of CONTROL: 0 : no reset occured 1 : reset occured Bit[14] Internal hardware status: 0 : no error occured 1 : internal error occured Bits[13:0] not of interest Reading of CONTROL will reset the bits[15,14] of CONTROL. After Power-on, bit[15] of CONTROL will be set; it must be read once to be resetted. 18 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 3.1.3. Protocol Description Write to DSP or Demodulator S Wait write device address ACK sub-addr ACK addr-byte ACK addr-byte ACK data-byte- ACK data-byte ACK P high low high low Read from DSP or Demodulator S Wait write device address ACK sub-addr ACK addr-byte ACK addr-byte ACK S high low read device address Wait ACK data-byte- ACK data-byte NAK P high low Write to Control or Test Registers S Wait write device address ACK sub-addr ACK data-byte ACK data-byte ACK P high low Note: S = P= ACK = NAK = Wait = I2C-Bus Start Condition from master I2C-Bus Stop Condition from master Acknowledge-Bit: LOW on I2C_DA from slave (= MSP, light gray) or master (= controller dark gray) Not Acknowledge-Bit: HIGH on I2C_DA from master (dark gray) to indicate `End of Read' or from MSP indicating internal error state I2C-Clock line is held low, while the MSP is processing the I2C command. This waiting time is max. 1 ms I2C_DA S I2C_CL 1 0 P Fig. 3-1: I2C bus protocol (MSB first; data must be stable while clock is high) MICRONAS INTERMETALL 19 MSP 34x1G 3.1.4. Proposals for General MSP 34x1G I2C Telegrams 3.1.4.1. Symbols daw dar < > aa dd write device address (80hex, 84hex or 88hex) read device address (81hex, 85hex or 89hex) Start Condition Stop Condition Address Byte Data Byte PRELIMINARY DATA SHEET 3.1.4.2. Write Telegrams 3.1.4.3. Read Telegrams 3.1.4.4. Examples <80 <80 <80 <80 <80 00 00 10 11 12 80 00 00 02 00 00> 00> 20 00 03> 00 <81 dd dd> 08 01 20> RESET MSP statically Clear RESET Set demodulator to stand. 03hex Read STATUS Set loudspeaker channel source to NICAM and Matrix to STEREO More examples of typical application protocols are listed in section "Programming Tips" on page 44. 20 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 3.2. Start-Up Sequence: Power-Up and I2C Controlling After POWER ON or RESET (see Fig. 4-24), the IC is in an inactive state. All registers are in the reset position (see tables 3-5 and 3-6), the analog outputs are muted. The controller has to initialize all registers for which a non-default setting is necessary. 3.3. MSP 34x1G Programming Interface 3.3.1. User Registers Overview The MSP 34x1G is controlled by means of user registers. The complete list of all user registers is given in the following tables. The registers are partitioned into the Demodulator section (Subaddress 10hex for writing, 11hex for reading) and the Baseband Processing sections (Subaddress 12hex for writing, 13hex for reading). Write and read registers are 16-bit wide, whereby the MSB is denoted bit [15]. Transmissions via I2C bus have to take place in 16-bit words (two byte transfers, with the most significant byte transferred first). All write registers, except the demodulator write registers, are readable. Unused parts of the 16-bit write registers must be zero. Addresses not given in this table must not be written. For reasons of software compatibility to the MSP 34x0D, an Manual/Compatibility Mode is available. More read and write registers together with a detailed description of this mode can be found in the "Appendix B: Manual/Compatibility Mode" on page 83. An overview of all MSP 34x1G Write Registers is shown in Table 3-5; all Read Registers are given in Table 3-6. MICRONAS INTERMETALL 21 MSP 34x1G PRELIMINARY DATA SHEET Table 3-5: List of MSP 34x1G Write Registers Write Register Address (hex) Bits Description and Adjustable Range Reset See Page I2C Subaddress = 10hex ; Registers are not readable STANDARD SELECT MODUS 00 20 00 30 [15..0] [15..0] Initial Programming of complete Demodulator Demodulator, Automatic and I2S options 00 00 00 00 26 28 I2C Subaddress = 12hex ; Registers are all readable by using I2C Subaddress = 13hex Volume loudspeaker channel Volume / Mode loudspeaker channel Balance loudspeaker channel [L/R] Balance mode loudspeaker Bass loudspeaker channel Treble loudspeaker channel Loudness loudspeaker channel Loudness filter characteristic Spatial effect strength loudspeaker ch. Spatial effect mode/customize Volume headphone channel Volume / Mode headphone channel Volume SCART1 output channel Loudspeaker source select Loudspeaker channel matrix Headphone source select Headphone channel matrix SCART1 source select SCART1 channel matrix I S source select I2S channel matrix Quasi-peak detector source select Quasi-peak detector matrix Prescale SCART input Prescale FM/AM FM matrix Prescale NICAM Prescale I S2 ACB : SCART Switches a. D_CTR_I/O Beeper Prescale I2S1 Mode tone control 2 2 00 00 [15..8] [7..0] [+12 dB ... -114 dB, MUTE] 1/8 dB Steps, Reduce Volume / Tone Control / Compromise [0...100 / 100% and 100 / 0...100%] [-127...0 / 0 and 0 / -127...0 dB] [Linear mode / logarithmic mode] [+20 dB ... -12 dB] [+15 dB ... -12 dB] [0 dB ... +17 dB] [NORMAL, SUPER_BASS] [-100%...OFF...+100%] [SBE, SBE+PSE] [+12 dB ... -114 dB, MUTE] 1/8 dB Steps, Reduce Volume / Tone Control [+12 dB ... -114 dB, MUTE] [FM/AM, NICAM, SCART, I S1, I S2] [SOUNDA, SOUNDB, STEREO, MONO...] [FM/AM, NICAM, SCART, I2S1, I2S2] [SOUNDA, SOUNDB, STEREO, MONO...] [FM/AM, NICAM, SCART, I2S1, I2S2] [SOUNDA, SOUNDB, STEREO, MONO...] [FM/AM, NICAM, SCART, I S1, I S2] [SOUNDA, SOUNDB, STEREO, MONO...] [FM/AM, NICAM, SCART, I S1, I S2] [SOUNDA, SOUNDB, STEREO, MONO...] [00hex ... 7Fhex] [00hex ... 7Fhex] [NO_MAT, GSTEREO, KSTEREO] [00hex ... 7Fhex] (MSP 3411G, MSP 3451G only) [00hex ... 7Fhex] Bits [15..0] [00hex ... 7Fhex]/[00hex ... 7Fhex] [00hex ... 7Fhex] [BASS/TREBLE, EQUALIZER] 2 2 2 2 2 2 MUTE 00hex 100%/100% linear mode 0 dB 0 dB 0 dB NORMAL OFF SBE+PSE MUTE 00hex MUTE FM/AM SOUNDA FM/AM SOUNDA FM/AM SOUNDA FM/AM SOUNDA FM/AM SOUNDA 00hex 00hex NO_MAT 00hex 10hex 00hex 00/00hex 10hex BASS/TREB 33 00 01 [15..8] [7..0] 34 00 02 00 03 00 04 [15..8] [15..8] [15..8] [7..0] 35 36 37 00 05 [15..8] [7..0] 38 00 06 [15..8] [7..0] 33 00 07 00 08 [15..8] [15..8] [7..0] 39 32 32 32 32 32 32 32 32 32 32 31 30 31 31 31 40 40 31 35 00 09 [15..8] [7..0] 00 0A [15..8] [7..0] 00 0B [15..8] [7..0] 00 0C [15..8] [7..0] 00 0D 00 0E [15..8] [15..8] [7..0] 00 10 00 12 00 13 00 14 00 16 00 20 [15..8] [15..8] [15..0] [15..0] [15..8] [15..8] 22 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-5: List of MSP 34x1G Write Registers, continued Write Register Equalizer loudspeaker ch. band 1 Equalizer loudspeaker ch. band 2 Equalizer loudspeaker ch. band 3 Equalizer loudspeaker ch. band 4 Equalizer loudspeaker ch. band 5 Automatic Volume Correction Subwoofer level adjust Subwoofer corner frequency Subwoofer complementary high-pass Balance headphone channel [L/R] Balance mode headphone Bass headphone channel Treble headphone channel Loudness headphone channel Loudness filter characteristic Volume SCART2 output channel SCART2 source select SCART2 channel matrix Virtual Surround OFF/ON switch Virtual Surround spatial effect strength Virtual Surround 3D effect strength Virtual Surround mode Noise generator 00 48 00 49 00 4A 00 4B 00 4D 00 40 00 41 00 31 00 32 00 33 00 30 Address (hex) 00 21 00 22 00 23 00 24 00 25 00 29 00 2C 00 2D Bits [15..8] [15..8] [15..8] [15..8] [15..8] [15..8] [15..8] [15..8] [7..0] [15..8] [7..0] [15..8] [15..8] [15..8] [7..0] [15..8] [15..8] [7..0] [15..8] [15..8] [15..8] [15..0] [15..0] Description and Adjustable Range [+12 dB ... -12 dB] [+12 dB ... -12 dB] [+12 dB ... -12 dB] [+12 dB ... -12 dB] [+12 dB ... -12 dB] [off, on, decay time] [0 dB ... -30 dB, mute] [50 Hz ... 400 Hz] [off, on] [0...100 / 100% and 100 / 0...100%] [-127...0 / 0 and 0 / -127...0 dB] [Linear mode / logarithmic mode] [+20 dB ... -12 dB] [+15 dB ... -12 dB] [0 dB ... +17 dB] [NORMAL, SUPER_BASS] [+12 dB ... -114 dB, MUTE] [FM, NICAM, SCART, I2S1, I2S2] Reset 0 dB 0 dB 0 dB 0 dB 0 dB off 0 dB 00hex off 100 %/100 % linear mode 0 dB 0 dB 0 dB NORMAL 00hex FM SOUNDA 00hex 00hex 00hex 00hex 00hex 39 32 32 41 41 41 41 42 35 36 37 See Page 36 36 36 36 36 34 39 39 39 34 [SOUNDA, SOUNDB, STEREO, MONO...] [OFF/ON] [0% - 100%] [0% - 100%] [PANORAMA/3D-PANORAMA] [OFF/ON, Noise_L, Noise_C, Noise_R, Noise_S] MICRONAS INTERMETALL 23 MSP 34x1G Table 3-6: List of MSP 34x1G Read Registers Read Register Address (hex) Bits Description and Adjustable Range PRELIMINARY DATA SHEET See Page I2C Subaddress = 11hex ; Registers are not writable STANDARD RESULT STATUS 00 7E 02 00 [15..0] [15..0] Result of Automatic Standard Detection (see Table 3-8) Monitoring of internal settings e.g. Stereo, Mono, Mute etc. . 29 29 I2C Subaddress = 13hex ; Registers are not writable Quasi peak readout left Quasi peak readout right MSP hardware version code MSP major revision code MSP product code MSP ROM version code 00 1F 00 19 00 1A 00 1E [15..0] [15..0] [15..8] [7..0] [15..8] [7..0] [00hex ... 7FFFhex]16 bit two's complement [00hex ... 7FFFhex]16 bit two's complement [00hex ... FFhex] [00hex ... FFhex] [00hex ... FFhex] [00hex ... FFhex] 43 43 43 43 43 43 24 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 3.3.2. Description of User Registers Table 3-7: Standard Codes for STANDARD SELECT register MSP Standard Code (Data in hex) TV Sound Standard Automatic Standard Detection 00 01 Start Automatic Standard Detection Standard Selection 00 02 00 03 00 04 00 05 00 06 M-Dual FM-Stereo B/G -Dual FM-Stereo1) D/K1-Dual FM-Stereo2) D/K2-Dual FM-Stereo 2) Sound Carrier Frequencies in MHz MSP 34x1G Version all 4.5/4.724212 5.5/5.7421875 6.5/6.2578125 6.5/6.7421875 6.5 3401, -11, -21, -41, -51 3401, -11, -51 D/K -FM-Mono with HDEV33), not detectable by Automatic Standard Detection, HDEV33) SAT-Mono (i.e. Eutelsat, s. Table 6-17) D/K3-Dual FM-Stereo B/G -NICAM-FM1) L -NICAM-AM I -NICAM-FM D/K -NICAM-FM 2) 4) 00 07 00 08 00 09 00 0A 00 0B 00 0C 00 0D 00 20 00 21 00 30 00 40 00 50 00 51 00 60 1) 2) 3) 4) 6.5/5.7421875 5.5/5.85 6.5/5.85 6.0/6.552 6.5/5.85 6.5/5.85 6.5/5.85 4.5 3421, -31, -41, -51 3411, -51 D/K -NICAM-FM with HDEV2 , not detectable by Automatic Standard Detection, for China D/K -NICAM-FM with HDEV33), not detectable by Automatic Standard Detection, for China BTSC-Stereo BTSC-Mono + SAP M-EIA-J Japan Stereo FM-Stereo Radio SAT-Mono (s. Table 6-17) SAT-Stereo (s. Table 6-17) SAT ADR (Astra Digital Radio) 4.5 10.7 6.5 7.02/7.20 7.2 3421, -41, -51 3421, -31, -41, -51 3401, -11, -51 In case of Automatic Sound Select, the B/G-codes 3hex and 8hex are equivalent. In case of Automatic Sound Select, the D/K-codes 4hex, 5hex and Bhex are equivalent. HDEV3: Max. FM deviation must not exceed 540 kHz HDEV2: Max. FM deviation must not exceed 360 kHz MICRONAS INTERMETALL 25 MSP 34x1G 3.3.2.1. STANDARD SELECT Register The TV sound standard of the MSP 34x1G demodulator is determined by the STANDARD SELECT register. There are two ways to use the STANDARD SELECT register: - Setting up the demodulator for a TV sound standard by sending the corresponding standard code with a single I2C-Bus transmission. - Starting the Automatic Standard Detection for terrestrial TV standards. This is the most comfortable way to set up the demodulator. Within 0.5 s, the detection and set-up of the actual TV sound standard is performed. The detected standard can be read out of the STANDARD RESULT register by the control processor. This feature is recommended for the primary set-up of a TV set. Outputs should be muted during Automatic Standard Detection. The Standard Codes are listed in Table 3-7. Selecting a TV sound standard via the STANDARD SELECT register initializes the demodulator. This includes: AGC, tuning frequency, band-pass filters, demodulation mode (FM, AM, or NICAM), carrier mute, deemphasis, and identification mode. If a present sound standard is impossible for a specific MSP version, it switches to the analog mono sound of this standard. In that case stereo or bilingual processing will not be possible. For a complete setup of the TV sound processing from analog IF input to the source selection, the transmissions as shown in Section 3.5. are necessary. Note: The FM matrix is set automatically if Automatic Sound Select is active (MODUS[0]=1). In this case, the FM matrix will be initialized with "Sound A Mono". During operation, the FM matrix will be automatically selected according to the actual identification information. For reasons of software compatibility to the MSP 34x0D, a Manual/Compatibility mode is available. A detailed description of this mode can be found on page 83. PRELIMINARY DATA SHEET 3.3.2.2. Refresh of STANDARD SELECT Register A general refresh of the STANDARD SELECT register is not allowed. However, the following method enables watching the MSP 34x1G "alive" status and detection of accidental resets (only versions A2 and later): - After Power-on, bit[15] of CONTROL will be set; it must be read once to enable the reset-detection feature. - Reading of the CONTROL register and checking the reset indicator bit[15] . - If bit[15] is "0", any refresh of the STANDARD SELECT register is not allowed. - If bit[15] is "1", indicating a reset, a refresh of the STANDARD SELECT register and all other MSPG registers is necessary. 26 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-8: Results of the Automatic Standard Detection Broadcasted Sound Standard Automatic Standard Detection could not find a sound standard B/G-FM B/G-NICAM I FM-Radio M-Korea M-Japan M-BTSC STANDARD RESULT Register Read 007Ehex 0000hex 3.3.2.3. STANDARD RESULT Register If Automatic Standard Detection is selected in the STANDARD SELECT register, status and result of the Automatic Standard Detection process can be read out of the STANDARD RESULT register. The possible results are based on the mentioned Standard Code and are listed in Table 3-8. In cases where no sound standard has been detected (no standard present, too much noise, strong interferers, etc.) the STANDARD RESULT register contains 00 00hex. In that case, the controller has to start further actions (for example, set the standard according to a preference list or by manual input). As long as the STANDARD RESULT register contains a value greater than 07 FFhex, the Automatic Standard Detection is still active. During this period, the MODUS and STANDARD SELECT register must not be written. The STATUS register will be updated when the Automatic Standard Detection has finished. If a present sound standard is impossible for a specific MSP version, it detects and switches to the analog mono sound of this standard. Example: The MSPs 3431G and 3441G will detect a B/G-NICAM signal as standard 3 and will switch to the analog FMMono sound. 0003hex 0008hex 000Ahex 0040hex 0002hex (if MODUS[14,13]=00) 0020hex (if MODUS[14,13]=01) 0030hex (if MODUS[14,13]=10) L-AM D/K1 D/K2 L-NICAM D/K-NICAM Automatic Standard Detection still active 0009hex (if MODUS[12]=0) 0004hex (if MODUS[12]=1) 0009hex (if MODUS[12]=0) 000Bhex (if MODUS[12]=1) >07FFhex MICRONAS INTERMETALL 27 MSP 34x1G 3.3.2.4. Write Registers on I2C Subaddress 10hex Table 3-9: Write Registers on I2C Subaddress 10hex Register Address Function PRELIMINARY DATA SHEET Name STANDARD SELECTION 00 20hex STANDARD SELECTION Register Defines TV Sound or FM-Radio Standard bit [15:0] 00 01hex 00 02hex ... 00 60hex MODUS 00 30hex MODUS Register General MSP 34x1G Options bit [0] bit [1] 0/1 0/1 off/on: Automatic Sound Select disable/enable STATUS change indication by means of the digital I/O pin D_CTR_I/O_1 Necessary condition: MODUS[3] = 0 (active) undefined, must be 0 state of digital output pins D_CTR_I/O_0 and _1 active: D_CTR_I/O_0 and _1 are output pins (can be set by means of the ACB register. see also: MODUS[1]) tristate: D_CTR_I/O_0 and _1 are input pins (level can be read out of STATUS[4,3]) active/tristate state of I2S output pins master/slave mode of I2S interface (must be set to 0 (= Master) in case of NICAM mode) Sony/Philips format of I2S word strobe active/tristate state of audio clock output pin AUD_CL_OUT ANA_IN_1+/ANA_IN_2+; select analog sound IF input pin undefined, must be 0 MODUS start Automatic Standard Detection Standard Codes (see Table 3-7)) STANDARD_SEL bit [2] bit [3] 0 0 1 bit [4] bit [5] bit [6] bit [7] bit [8] bit [11:9] 0/1 0/1 0/1 0/1 0/1 0 Preference in Automatic Standard Detection: bit [12] 0 1 bit [14:13] 0 1 2 3 bit [15] 1) Valid detected 6.5 MHz carrier is interpreted as:1) standard L (SECAM) standard D/K1, D/K2 or D/K NICAM detected 4.5 MHz carrier is interpreted as:1) standard M (Korea) standard M (BTSC) standard M (Japan) carrier at 4.5 MHz is ignored (chroma carrier) undefined, must be 0 0 at the next start of Automatic Standard Detection. 28 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 3.3.2.5. Read Registers on I2C Subaddress 11hex Table 3-10: Read Registers on I2C Subaddress 11hex Register Address Function Name STANDARD RESULT 00 7Ehex STANDARD RESULT Register Readback of the detected TV Sound or FM-Radio Standard bit [15:0] 00 00hex Automatic Standard Detection could not find a sound standard MSP Standard Codes (see Table 3-8) STANDARD_RES 00 02hex ... 00 40hex >07 FFhex Automatic Standard Detection still active STATUS 02 00hex STATUS Register STATUS Contains all user relevant internal information about the status of the MSP bit [0] bit [1] bit [2] bit [3] bit [4] bit [5,9] 0 1 0 1 0/1 0/1 00 01 10 11 undefined detected primary carrier (Mono or MPX carrier) no primary carrier detected detected secondary carrier (2nd A2 or SAP carrier) no secondary carrier detected low/high level of digital I/O pin D_CTR_I/O_0 low/high level of digital I/O pin D_CTR_I/O_1 analog sound standard (FM or AM) active not obtainable digital sound (NICAM) available (MSP 3411G and MSP 3451G only) bad reception condition of digital sound (NICAM) due to: a. high error rate b. unimplemented sound code c. data transmission only mono/stereo indication "1" indicates independent mono sound (only for NICAM on MSP 3411G and MSP 3451G) "1" indicates bilingual sound mode or SAP present undefined bit [6] bit [7] bit [8] bit [15:10] 0/1 0/1 0/1 If STATUS change indication is activated by means of MODUS[1]: Each change in the STATUS register sets the digital I/O pin D_CTR_I/O_1 to high level. Reading the STATUS register resets D_CTR_I/O_1. MICRONAS INTERMETALL 29 MSP 34x1G 3.3.2.6. Write Registers on I2C Subaddress 12hex Table 3-11: Write Registers on I2C Subaddress 12hex Register Address Function PRELIMINARY DATA SHEET Name PREPROCESSING 00 0Ehex FM/AM Prescale bit [15:8] 00hex ... 7Fhex 00hex Defines the input prescale gain for the demodulated FM or AM signal off (RESET condition) PRE_FM For all FM modes except satellite FM and AM-mode, the combinations of prescale value and FM deviation listed below lead to internal full scale. FM mode bit [15:8] 7Fhex 48hex 30hex 24hex 18hex 13hex 28 kHz FM deviation 50 kHz FM deviation 75 kHz FM deviation 100 kHz FM deviation 150 kHz FM deviation 180 kHz FM deviation (limit) FM high deviation mode (HDEV2, MSP Standard Code = Chex) bit [15:8] 30hex 14hex 150 kHz FM deviation 360 kHz FM deviation (limit) FM very high deviation mode (HDEV3, MSP Standard Code = 6 and Dhex) bit [15:8] 20hex 1Ahex 450 kHz FM deviation 540 kHz FM deviation (limit) Satellite FM with adaptive deemphasis bit [15:8] 10hex recommendation AM mode (MSP Standard Code = 9) bit [15:8] 7Chex recommendation for SIF input levels from 0.1 Vpp to 0.8 Vpp (Due to the AGC being switched on, the AM-output level remains stable and independent of the actual SIF-level in the mentioned input range) 30 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address (continued) Function FM Matrix Modes Defines the dematrix function for the demodulated FM signal bit [7:0] 00hex 01hex 02hex 03hex 04hex no matrix (used for bilingual and unmatrixed stereo sound) German stereo (Standard B/G) Korean stereo (also used for BTSC, EIA-J and FM Radio) sound A mono (left and right channel contain the mono sound of the FM/AM mono carrier) sound B mono Name FM_MATRIX 00 0Ehex In case of Automatic Sound Select, the FM Matrix Mode is set automatically, i.e. the low-part of any I2C transmission to the register 00 0Ehex is ignored. To enable a Forced Mono Mode for all analog stereo systems by overriding the internal pilot or identification evaluation, the following steps must be transmitted: 1. MODUS with bit[0] = 0 (Automatic Sound Select off) 2. FM Presc./Matrix with FM Matrix = Sound A Mono (SAP: Sound B Mono) 3. Select FM/AM source channel, with channel matrix set to "Stereo" (transparent) 00 10hex NICAM Prescale Defines the input prescale value for the digital NICAM signal bit [15:8] 00hex ... 7Fhex prescale gain examples: off 00hex 0 dB gain 20hex 9 dB gain (recommendation) 5Ahex +12 dB gain (maximum gain) 7Fhex 00 16hex 00 12hex I2S1 Prescale I2S2 Prescale Defines the input prescale value for digital I2S input signals bit [15:8] 00hex ... 7Fhex prescale gain examples: off 00hex 0 dB gain (recommendation) 10hex +18 dB gain (maximum gain) 7Fhex 00 0Dhex SCART Input Prescale Defines the input prescale value for the analog SCART input signal bit [15:8] 00hex ... 7Fhex prescale gain examples: off 00hex 0 dB gain (2 VRMS input leads to digital full scale) 19hex Due to the Dolby requirements, this is the maximum value allowed to prohibit clipping of a 2 VRMS input signal. +14 dB gain (400 mVRMS input leads to digital full scale) 7Fhex PRE_SCART PRE_I2S1 PRE_I2S2 PRE_NICAM MICRONAS INTERMETALL 31 MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address Function PRELIMINARY DATA SHEET Name SOURCE SELECT AND OUTPUT CHANNEL MATRIX 00 08hex 00 09hex 00 0Ahex 00 41hex 00 0Bhex 00 0Chex Source for: Loudspeaker Output Headphone Output SCART1 DA Output SCART2 DA Output I2S Output Quasi-Peak Detector bit [15:8] 0 1 "FM/AM": demodulated FM or AM mono signal "Stereo or A/B": demodulator Stereo or A/B signal (in manual mode, this source is identical to the NICAM source in the MSP 3410D) "Stereo or A": demodulator Stereo Sound or Language A (only defined for Automatic Sound Select) "Stereo or B": demodulator Stereo Sound or Language B (only defined for Automatic Sound Select) SCART input I2S1 input I2S2 input SRC_MAIN SRC_AUX SRC_SCART1 SRC_SCART2 SRC_I2S SRC_QPEAK 3 4 2 5 6 For demodulator sources, see Table 2-2. 00 08hex 00 09hex 00 0Ahex 00 41hex 00 0Bhex 00 0Chex Matrix Mode for: Loudspeaker Output Headphone Output SCART1 DA Output SCART2 DA Output I2S Output Quasi-Peak Detector bit [7:0] Sound A Mono (or Left Mono) 00hex Sound B Mono (or Right Mono) 10hex Stereo (transparent mode) 20hex Mono (sum of left and right inputs divided by 2) 30hex special modes are available (see Section 6.5.1. on page 95) MAT_MAIN MAT_AUX MAT_SCART1 MAT_SCART2 MAT_I2S MAT_QPEAK In Automatic Sound Select mode, the demodulator source channels are set according to Table 2-2. Therefore, the matrix modes of the corresponding output channels should be set to "Stereo" (transparent). 32 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address Function Name LOUDSPEAKER AND HEADPHONE PROCESSING 00 00hex 00 06hex Volume Loudspeaker Volume Headphone bit [15:8] volume table with 1 dB step size +12 dB (maximum volume) 7Fhex 7Ehex +11 dB ... 74hex +1 dB 73hex 0 dB -1 dB 72hex ... 02hex -113 dB 01hex -114 dB 00hex Mute (reset condition) Fast Mute (needs about 75 ms until the signal is comFFhex pletely ramped down) bit [7:5] higher resolution volume table 0 +0 dB 1 +0.125 dB increase in addition to the volume table ... 7 +0.875 dB increase in addition to the volume table 0 must be set to 0 VOL_MAIN VOL_AUX bit [4] bit [3:0] clipping mode 0 reduce volume 1 reduce tone control 2 compromise mode With large scale input signals, positive volume settings may lead to signal clipping. The MSP 34x1G loudspeaker and headphone volume function is divided into a digital and an analog section. With Fast Mute, volume is reduced to mute position by digital volume only. Analog volume is not changed. This reduces any audible DC plops. To turn volume on again, the volume step that has been used before Fast Mute was activated must be transmitted. If the clipping mode is set to "Reduce Volume", the following rule is used: To prevent severe clipping effects with bass, treble, or equalizer boosts, the internal volume is automatically limited to a level where, in combination with either bass, treble, or equalizer setting, the amplification does not exceed 12 dB. If the clipping mode is "Reduce Tone Control", the bass or treble value is reduced if amplification exceeds 12 dB. If the equalizer is switched on, the gain of those bands is reduced, where amplification together with volume exceeds 12 dB. If the clipping mode is "Compromise Mode", the bass or treble value and volume are reduced half and half if amplification exceeds 12 dB. If the equalizer is switched on, the gain of those bands is reduced half and half, where amplification together with volume exceeds 12 dB. Example: Red. Volume Red. Tone Con. Compromise Vol.: +6 dB 3 6 4.5 Bass: +9 dB 9 6 7.5 Treble: +5 dB 5 5 5 MICRONAS INTERMETALL 33 MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address 00 29hex Function Automatic Volume Correction (AVC) Loudspeaker Channel bit [15:12] 00hex 08hex bit [11:8] 08hex 04hex 02hex 01hex AVC off (and reset internal variables) AVC on PRELIMINARY DATA SHEET Name AVC 8 sec decay time 4 sec decay time 2 sec decay time 20 ms decay time (intended for quick adaptation to the average volume level after channel change) Note: To reset the internal variables, the AVC should be switched off and then on again during any channel or source change. For standard applications, the recommended decay time is 4 sec. Note: AVC should not be used in any Dolby Prologic mode (with DPL 35xx), except in PANORAMA or 3D-PANORAMA mode, when only the loudspeaker output is active. 00 01hex 00 30hex Balance Loudspeaker Channel Balance Headphone Channel bit [3:0] Balance Mode linear 0hex logarithmic 1hex BAL_MAIN BAL_AUX bit [15:8] Linear Mode Left muted, Right 100% 7Fhex Left 0.8%, Right 100% 7Ehex ... Left 99.2%, Right 100% 01hex Left 100%, Right 100% 00hex Left 100%, Right 99.2% FFhex ... Left 100%, Right 0.8% 82hex Left 100%, Right muted 81hex bit [15:8] Logarithmic Mode Left -127 dB, Right 0 dB 7Fhex Left -126 dB, Right 0 dB 7Ehex ... Left -1 dB, Right 0 dB 01hex Left 0 dB, Right 0 dB 00hex Left 0 dB, Right -1 dB FFhex ... Left 0 dB, Right -127 dB 81hex Left 0 dB, Right -128 dB 80hex Positive balance settings reduce the left channel without affecting the right channel; negative settings reduce the right channel leaving the left channel unaffected. 34 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address 00 20hex Function Tone Control Mode Loudspeaker Channel bit [15:8] 00hex FFhex bass and treble is active equalizer is active Name TONE_MODE Defines whether Bass/Treble or Equalizer is activated for the loudspeaker channel. Bass and Equalizer cannot work simultaneously. If Equalizer is used, Bass, and Treble coefficients must be set to zero and vice versa. 00 02hex 00 31hex Bass Loudspeaker Channel Bass Headphone Channel bit [15:8] normal range +12 dB 60hex 58hex +11 dB ... 08hex +1 dB 00hex 0 dB -1 dB F8hex ... A8hex -11 dB A0hex -12 dB bit [15:8] extended range 7Fhex +20 dB 78hex +18 dB 70hex +16 dB 68hex +14 dB Higher resolution is possible: an LSB step in the normal range results in a gain step of about 1/8 dB, in the extended range about 1/4 dB. With positive bass settings, internal clipping may occur even with overall volume less than 0 dB. This will lead to a clipped output signal. Therefore, it is not recommended to set bass to a value that, in conjunction with volume, would result in an overall positive gain. BASS_MAIN BASS_AUX MICRONAS INTERMETALL 35 MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address 00 03hex 00 32hex Function Treble Loudspeaker Channel Treble Headphone Channel bit [15:8] 78hex 70hex ... 08hex 00hex F8hex ... A8hex A0hex +15 dB +14 dB +1 dB 0 dB -1 dB -11 dB -12 dB PRELIMINARY DATA SHEET Name TREB_MAIN TREB_AUX Higher resolution is possible: an LSB step results in a gain step of about 1/8 dB. With positive treble settings, internal clipping may occur even with overall volume less than 0 dB. This will lead to a clipped output signal. Therefore, it is not recommended to set treble to a value that, in conjunction with volume, would result in an overall positive gain. 00 21hex 00 22hex 00 23hex 00 24hex 00 25hex Equalizer Loudspeaker Channel Band 1 (below 120 Hz) Equalizer Loudspeaker Channel Band 2 (center: 500 Hz) Equalizer Loudspeaker Channel Band 3 (center: 1.5 kHz) Equalizer Loudspeaker Channel Band 4 (center: 5 kHz) Equalizer Loudspeaker Channel Band 5 (above: 10 kHz) bit [15:8] 60hex 58hex ... 08hex 00hex F8hex ... A8hex A0hex +12 dB +11 dB +1 dB 0 dB -1 dB -11 dB -12 dB EQUAL_BAND1 EQUAL_BAND2 EQUAL_BAND3 EQUAL_BAND4 EQUAL_BAND5 Higher resolution is possible: an LSB step results in a gain step of about 1/8 dB. With positive equalizer settings, internal clipping may occur even with overall volume less than 0 dB. This will lead to a clipped output signal. Therefore, it is not recommended to set equalizer bands to a value that, in conjunction with volume, would result in an overall positive gain. 36 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address 00 04hex 00 33hex Function Loudness Loudspeaker Channel Loudness Headphone Channel bit [15:8] Loudness Gain +17 dB 44hex 40hex +16 dB ... 04hex +1 dB 00hex 0 dB bit [7:0] Loudness Mode normal (constant volume at 1 kHz) 00hex Super Bass (constant volume at 2 kHz) 04hex Name LOUD_MAIN LOUD_AUX Higher resolution of Loudness Gain is possible: An LSB step results in a gain step of about 1/4 dB. Loudness increases the volume of low- and high-frequency signals, while keeping the amplitude of the 1-kHz reference frequency constant. The intended loudness has to be set according to the actual volume setting. Because loudness introduces gain, it is not recommended to set loudness to a value that, in conjunction with volume, would result in an overall positive gain. The corner frequency for bass amplification can be set to two different values. In Super Bass mode, the corner frequency is shifted up. The point of constant volume is shifted from 1 kHz to 2 kHz. MICRONAS INTERMETALL 37 MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address 00 05hex Function Spatial Effects Loudspeaker Channel bit [15:8] Effect Strength Enlargement 100% 7Fhex Enlargement 50% 3Fhex ... Enlargement 1.5% 01hex Effect off 00hex reduction 1.5% FFhex ... reduction 50% C0hex reduction 100% 80hex bit [7:4] PRELIMINARY DATA SHEET Name SPAT_MAIN Spatial Effect Mode Stereo Basewidth Enlargement (SBE) and 0hex Pseudo Stereo Effect (PSE). (Mode A) Stereo Basewidth Enlargement (SBE) only. (Mode B) 2hex Spatial Effect High-Pass Gain max. high-pass gain 0hex 2/3 high-pass gain 2hex 1/3 high-pass gain 4hex min. high-pass gain 6hex automatic 8hex bit [3:0] Spatial effects should not be used together with 3D-PANORAMA or PANORAMA. There are several spatial effect modes available: In mode A (low byte = 00hex), the spatial effect depends on the source mode. If the incoming signal is mono, Pseudo Stereo Effect is active; for stereo signals, Pseudo Stereo Effect and Stereo Basewidth Enlargement is effective. The strength of the effect is controllable by the upper byte. A negative value reduces the stereo image. A strong spatial effect is recommended for small TV sets where loudspeaker spacing is rather close. For large screen TV sets, a more moderate spatial effect is recommended. In mode B, only Stereo Basewidth Enlargement is effective. For mono input signals, the Pseudo Stereo Effect has to be switched on. It is worth mentioning, that all spatial effects affect amplitude and phase response. With the lower 4 bits, the frequency response can be customized. A value of 0hex yields a flat response for center signals (L = R), but a high-pass function for L or R only signals. A value of 6hex has a flat response for L or R only signals, but a low-pass function for center signals. By using 8hex, the frequency response is automatically adapted to the sound material by choosing an optimal high-pass gain. 38 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address Function Name SUBWOOFER OUTPUT CHANNEL 00 2Chex Subwoofer Level Adjustment bit [15:8] 00hex FFhex ... E3hex E2hex ... 80hex 00 2Dhex 0 dB -1 dB -29 dB -30 dB Mute SUBW_FREQ SUBW_LEVEL Subwoofer Corner Frequency bit [15:8] 5...40 corner frequency in 10-Hz steps (range: 50...400 Hz) Subwoofer Complementary High-Pass Filter bit [7:0] 00hex 01hex loudspeaker channel unfiltered a complementary high-pass is processed in the loudspeaker output channel SUBW_HP SCART OUTPUT CHANNEL 00 07hex 00 40hex Volume SCART1 Output Channel Volume SCART2 Output Channel bit [15:8] volume table with 1 dB step size +12 dB (maximum volume) 7Fhex 7Ehex +11 dB ... 74hex +1 dB 73hex 0 dB -1 dB 72hex ... 02hex -113 dB 01hex -114 dB 00hex Mute (reset condition) bit [7:5] higher resolution volume table 0 +0 dB 1 +0.125 dB increase in addition to the volume table ... 7 +0.875 dB increase in addition to the volume table 01hex this must be 01hex VOL_SCART1 VOL_SCART2 bit [4:0] MICRONAS INTERMETALL 39 MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address Function PRELIMINARY DATA SHEET Name SCART SWITCHES AND DIGITAL I/O PINS 00 13hex ACB Register Defines the level of the digital output pins and the position of the SCART switches bit [15] bit [14] 0/1 0/1 low/high of digital output pin D_CTR_I/O_0 (MODUS[3]=0) low/high of digital output pin D_CTR_I/O_1 (MODUS[3]=0) ACB_REG bit [13:5] SCART DSP Input Select xxxx00xx0 SCART1 to DSP input (RESET position) xxxx01xx0 MONO to DSP input (Sound A Mono must be selected in the channel matrix mode for the corresponding output channels) xxxx10xx0 SCART2 to DSP input xxxx11xx0 SCART3 to DSP input xxxx00xx1 SCART4 to DSP input xxxx11xx1 mute DSP input bit [13:5] SCART1 Output Select xx00xxx0x SCART3 input to SCART1 output (RESET position) xx01xxx0x SCART2 input to SCART1 output xx10xxx0x MONO input to SCART1 output xx11xxx0x SCART1 DA to SCART1 output xx00xxx1x SCART2 DA to SCART1 output xx01xxx1x SCART1 input to SCART1 output xx10xxx1x SCART4 input to SCART1 output xx11xxx1x mute SCART1 output bit [13:5] SCART2 Output Select 00xxxx0xx SCART1 DA to SCART2 output (RESET position) 01xxxx0xx SCART1 input to SCART2 output 10xxxx0xx MONO input to SCART2 output 00xxxx1xx SCART2 DA to SCART2 output 01xxxx1xx SCART2 input to SCART2 output 10xxxx1xx SCART3 input to SCART2 output 11xxxx1xx SCART4 input to SCART2 output 11xxxx0xx mute SCART2 output The RESET position becomes active at the time of the first write transmission on the control bus to the audio processing part. By writing to the ACB register first, the RESET state can be redefined. BEEPER 00 14hex Beeper Volume and Frequency bit [15:8] Beeper Volume off 00hex maximum volume 7Fhex bit [7:0] Beeper Frequency 16 Hz (lowest) 01hex 1 kHz 40hex 4 kHz FFhex BEEPER 40 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address Function Name VIRTUAL SURROUND PROCESSING 00 48hex Virtual Surround OFF/ON Switch bit [15:8] 00hex 01hex bit [7:0] 00hex virtual surround sound off (normal baseband processing) virtual surround processing must be 0 VIRT_ON Be sure to switch off Spatial Effects Loudspeaker Channel (register 0005hex) if 3D-PANORAMA is in use. 00 49hex Virtual Surround Spatial Effects bit [15:8] Spatial Effect Strength Enlargement 100% 7Fhex Enlargement 50% 3Fhex ... Enlargement 1.5% 01hex Effect off 00hex bit [7:0] 00hex must be 0 VIRT_SPAT Increases the perceived basewidth of the reproduced left and right front channels. Recommended value: 50% = 40hex. In contrast to the spatial effect for the loudspeaker channel, the surround spatial effect is optimized for virtual surround. 00 4Ahex Virtual Surround 3D Effect Strength bit [15:8] Virtual Surround Effect Strength Effect 100% 7Fhex Effect 50% 3Fhex ... Effect 1.5% 01hex Effect off 00hex bit [7:0] 00hex must be 0 VIRT_3DEFF Strength of the surround effect in PANORAMA or 3D-PANORAMA mode. Recommended value: 66% = 54hex. 00 4Bhex Virtual Surround Mode bit [15:8] 00hex bit [7:0] 50hex 60hex must be 0 PANORAMA virtualizer 3D-PANORAMA virtualizer VIRT_MODE MICRONAS INTERMETALL 41 MSP 34x1G Table 3-11: Write Registers on I2C Subaddress 12hex, continued Register Address Function PRELIMINARY DATA SHEET Name NOISE GENERATOR 00 4Dhex Noise Generator bit [15:8] 00hex 80hex bit [7:0] A0hex B0hex C0hex D0hex Noise generator off Noise generator on Noise on left channel Noise on center channel Noise on right channel Noise on surround channel NOISE_CHAN Determines the active channel for the noise generator. 42 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 3.3.2.7. Read Registers on I2C Subaddress 13hex Table 3-12: Read Registers on I2C Subaddress 13hex Register Address Function Name QUASI-PEAK DETECTOR READOUT 00 19hex 00 1Ahex Quasi-Peak Detector Readout Left Quasi-Peak Detector Readout Right bit [15..0] 0hex... 7FFFhex values are 16 bit two's complement (only positive) MSP 34X1G VERSION READOUT REGISTERS 00 1Ehex MSP Hardware Version Code bit [15..8] 01hex MSP 34x1G - A1 MSP_HARD QPEAK_L QPEAK_R A change in the hardware version code defines hardware optimizations that may have influence on the chip's behavior. The readout of this register is identical to the hardware version code in the chip's imprint. MSP Major Revision Code bit [7..0] 07hex MSP 34x1G - A1 MSP_REVISION The major revision code of the MSP 34x1G is 7. 00 1Fhex MSP Product Code bit [15..8] 01hex 0Bhex 1Fhex 29hex 33hex MSP 3401G - A1 MSP 3411G - A1 MSP 3431G - A1 MSP 3441G - A1 MSP 3451G - A1 MSP_PRODUCT By means of the MSP-Product Code, the control processor is able to decide which TV sound standards have to be considered. MSP ROM Version Code bit [7..0] 41hex 42hex MSP 34x1G - A1 MSP 34x1G - A2 MSP_ROM A change in the ROM version code defines internal software optimizations, that may have influence on the chip's behavior, e.g. new features may have been included. While a software change is intended to create no compatibility problems, customers that want to use the new functions can identify new MSP 34x1G versions according to this number. To avoid compatibility problems with MSP 3410B and MSP 34x0D, an offset of 40hex is added to the ROM version code of the chip's imprint. MICRONAS INTERMETALL 43 MSP 34x1G 3.4. Programming Tips This section describes the preferred method for initializing the MSP 34x1G. The initialization is grouped into four sections: analog signal path, demodulator input, input processing for SCART and I2S, and output processing. See Fig. 2-1 on page 9 for a complete signal flow. PRELIMINARY DATA SHEET 3.5. Examples of Minimum Initialization Codes Initialization of the MSP 34x1G according to these listings reproduces sound of the selected standard on the loudspeaker output. All numbers are hexadecimal. The examples have the following structure: 1. Perform an I2C controlled reset of the IC. 2. Write MODUS register (with Automatic Sound Select). SCART Signal Path 1. Select analog input for the SCART baseband processing (SCART DSP Input Select) by means of the ACB register. 2. Select the source for each analog SCART output (SCART Output Select) by means of the ACB register. 3. Set Source Selection for loudspeaker channel (with matrix set to STEREO). 4. Set Prescale (FM and/or NICAM and dummy FM matrix). 5. Write STANDARD SELECT register. 6. Set Volume loudspeaker channel to 0 dB. Demodulator Input For a complete setup of the TV sound processing from analog IF input to the source selection, the following steps must be performed: 1. Set MODUS register to the preferred mode and Sound IF input. 2. Choose preferred prescale (FM and NICAM) values. 3. Write STANDARD SELECT register. If Automatic Sound Select is not active, the following step has to be done repeatedly: 4. Choose FM matrix according to the sound mode indicated in the STATUS register. 2S 3.5.1. SCART1 Input to Loudspeaker in Stereo Sound <80 00 00 00 80 00> <80 00 00 00 00 00> <80 12 00 08 02 20> <80 12 00 0d 19 00> <80 12 00 00 73 00> // source loudspeaker = scart, stereo // prescale scart // volume main = 0dB // reset 3.5.2. SCART1 Input to Loudspeaker in 3D-PANORAMA Sound <80 00 00 00 80 00> <80 00 00 00 00 00> <80 12 00 08 02 20> <80 12 00 0d 19 00> <80 12 00 00 73 00> <80 12 00 48 01 00> <80 12 00 49 40 00> <80 12 00 4a 54 00> <80 12 00 4b 00 60> <80 12 00 4d 00 00> // source loudspeaker = scart, stereo // prescale scart // volume main = 0dB // virtual surround sound: on // Surround spatial effect = 50% // panorama sound effect = 66% // Surround mode = 3d_panorama // Noise Sequencer = off // reset SCART and I Inputs 2S 1. Select preferred prescale for SCART. 2. Select preferred prescale for I (set to 0 dB after RESET). inputs Output Channels 1. Select the source channel and matrix for each output channel. 2. Set audio baseband processing. 3. Select volume for each output channel. 3.5.3. Noise Sequencer for 3D-PANORAMA Sound // switch into 3D-PANORAMA sound (s.a.). Then: <80 12 00 4d 80 a0> [wait for 2 seconds] <80 12 00 4d 80 b0> [wait for 2 seconds] <80 12 00 4d 80 c0> [wait for 2 seconds] <80 12 00 4d 80 d0> [wait for 2 seconds] // switch back to normal operation <80 12 00 4d 00 00> // Noise Sequencer = off // noise S // noise R // noise C // noise L 44 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 3.5.7. FM-Stereo Radio <80 00 80 00> <80 00 00 00> <80 10 00 30 20 03> <80 12 00 08 03 20> <80 12 00 0E 24 03> <80 10 00 20 00 40> <80 12 00 00 73 00> // Softreset // MODUS-Register: Automatic = on // Source Sel. = (St or A) & Ch. Matr. = St // FM/AM-Prescale = 24hex, FM-Matrix = Sound A Mono // Standard Select: FM-STEREO-RADIO // Loudspeaker Volume 0 dB 3.5.4. B/G-FM (A2 or NICAM) <80 00 80 00> <80 00 00 00> <80 10 00 30 20 03> <80 12 00 08 03 20> <80 12 00 0E 24 03> <80 12 00 10 00 5A> <80 10 00 20 00 03> or <80 10 00 20 00 08> <80 12 00 00 73 00> // MODUS-Register: Automatic = on // Source Sel. = (St or A) & Ch. Matr. = St // FM/AM-Prescale = 24hex, FM-Matrix = MONO/SOUNDA // NICAM-Prescale = 5Ahex // Standard Select: A2 B/G or NICAM B/G // Softreset // Loudspeaker Volume 0 dB 3.5.8. Automatic Standard Detection A detailed software flow diagram is shown in Fig. 3-2 on page 46. 3.5.5. BTSC-Stereo <80 00 80 00> <80 00 00 00> <80 10 00 30 20 03> <80 12 00 08 03 20> <80 12 00 0E 24 03> <80 10 00 20 00 20> <80 12 00 00 73 00> // MODUS-Register: Automatic = on // Source Sel. = (St or A) & Ch. Matr. = St // FM/AM-Prescale = 24hex, FM-Matrix = Sound A Mono // Standard Select: BTSC-STEREO // Loudspeaker Volume 0 dB // Softreset <80 00 80 00> <80 00 00 00> <80 10 00 30 20 03> <80 12 00 08 03 20> <80 12 00 0E 24 03> <80 12 00 10 00 5A> <80 10 00 20 00 01> // Softreset // MODUS-Register: Automatic = on // Source Sel. = (St or A) & Ch. Matr. = St // FM/AM-Prescale = 24hex, FM-Matrix = Sound A Mono // NICAM-Prescale = 5Ahex // Standard Select: Automatic Standard Detection 3.5.6. BTSC-SAP with SAP at Loudspeaker Channel <80 00 80 00> <80 00 00 00> <80 10 00 30 20 03> <80 12 00 08 04 20> <80 12 00 0E 24 03> <80 10 00 20 00 21> <80 12 00 00 73 00> // MODUS-Register: Automatic = on // Source Sel. = (St or B) & Ch. Matr. = St // FM/AM-Prescale = 24hex, FM-Matrix = Sound A Mono // Standard Select: BTSC-SAP // Loudspeaker Volume 0 dB // Softreset // Wait till STANDARD RESULT contains a value 07FF // IF STANDARD RESULT contains 0000 // do some error handling // ELSE <80 12 00 00 73 00> // Loudspeaker Volume 0 dB 3.5.9. Software Flow for Interrupt driven STATUS Check A detailed software flow diagram is shown in Fig. 3-2 on page 46. If the D_CTR_I/O_1 pin of the MSP 34x1G is connected to an interrupt input pin of the controller, the following interrupt handler can be applied to be automatically called with each status change of the MSP 34x1G. The interrupt handler may adjust the TV display according to the new status information. Interrupt Handler: <80 11 02 00 <81 dd dd> // Read STATUS // adjust TV display with given status information // Return from Interrupt MICRONAS INTERMETALL 45 MSP 34x1G PRELIMINARY DATA SHEET Write MODUS Register: Example for the essential bits: [0] = 1 Automatic Sound Select = on [1] = 1 Enable interrupt if STATUS changes [8] = 0 ANA_IN1+ is selected Define Preference for Automatic Standard Detection: [12] = 0 If 6.5 MHz, set SECAM-L [14:13] = 3 Ignore 4.5 MHz carrier Write SOURCE SELECT Settings Example: set loudspeaker Source Select to "Stereo or A" set headphone Source Select to "Stereo or B" set SCART_Out Source Select to "Stereo or A/B" set Channel Matrix mode for all outputs to "Stereo" Write FM/AM-Prescale Write NICAM-Prescale Write 01 into STANDARD SELECT Register (Start Automatic Standard Detection) set previous standard or set standard manually according picture information yes Result = 0 ? no expecting MSPG-interrupt In case of MSPGInterrupt to Controller: Read STATUS Adjust TV-Display If Bilingual, adjust Source Select setting if required Fig. 3-2: Software flow diagram for a Minimum demodulator setup for a European Multistandard TV set applying the Automatic Sound Select feature 46 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4. Specifications 4.1. Outline Dimensions 0.9 0.2 16 x 1.27 = 20.32 0.1 1.27 1.2 x 45 1.1 x 45 9 10 2 9 0.71 0.05 25.14 0.12 1 61 60 0.48 0.06 7.5 9 0.23 0.04 7.5 26 27 25.14 0.12 43 44 1.9 0.05 4.05 0.1 4.75 0.15 0.1 24.2 0.1 SPGS0027-2(P68)/1E Fig. 4-1: 68-Pin Plastic Leaded Chip Carrier Package (PLCC68) Weight approximately 4.8 g Dimensions in mm SPGS0016-5(P64)/1E SPGS0016-5(P52)/1E 64 33 52 27 1 1 32 26 47.0 0.1 57.7 0.1 0.8 0.2 3.8 0.1 19.3 0.1 18 0.05 0.6 0.2 4.0 0.1 15.6 0.1 14 0.1 0.28 0.06 2.8 0.2 0.28 0.06 3.2 0.2 1 0.05 1.778 0.48 0.06 31 x 1.778 = 55.1 0.1 20.3 0.5 1 0.05 1.778 0.48 0.06 25 x 1.778 = 44.4 0.1 16.3 1 Fig. 4-2: 64-Pin Plastic Shrink Dual-Inline Package (PSDIP64) Weight approximately 9.0 g Dimensions in mm Fig. 4-3: 52-Pin Plastic Shrink Dual-Inline Package (PSDIP52) Weight approximately 5.5 g Dimensions in mm MICRONAS INTERMETALL 16 x 1.27 = 20.32 23.3 0.3 24.2 0.1 0.1 2 1.27 47 MSP 34x1G PRELIMINARY DATA SHEET 0.17 0.04 64 65 1.8 10.3 9.8 16 8 0.37 0.05 14 0.1 41 40 23 x 0.8 = 18.4 0.1 0.8 17.2 0.15 1.8 8 5 80 1 25 1.3 0.05 2.7 0.1 3 0.2 0.1 20 0.1 24 23.2 0.15 SPGS705000-1(P80)/1E Fig. 4-4: 80-Pin Plastic Quad Flat Pack (PQFP80) Weight approximately 1.61 g Dimensions in mm 15 x 0.5 = 7.5 0.1 0.145 0.055 48 49 12 0.2 33 15 x 0.5 = 7.5 0.1 32 10 0.1 0.5 0.5 1.75 64 1 1.75 12 0.2 16 17 1.4 0.05 1.5 0.1 0.1 10 0.1 0.22 0.05 D0025/3E Fig. 4-5: 64-Pin Plastic Low-Profile Quad Flat Pack (PLQFP64) Weight approximately 3.5 g Dimensions in mm 48 MICRONAS INTERMETALL 15 x 0.8 = 12.0 0.1 0.8 PRELIMINARY DATA SHEET MSP 34x1G 4.2. Pin Connections and Short Descriptions NC = not connected; leave vacant LV = if not used, leave vacant OBL = obligatory; connect as described in circuit diagram DVSS: if not used, connect to DVSS AHVSS: connect to AHVSS Pin No. PLCC 68-pin PSDIP 64-pin PSDIP 52-pin PQFP 80-pin PLQFP 64-pin Pin Name Type Connection (if not used) Short Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 16 - 15 14 13 12 11 10 9 8 7 6 5 4 3 2 - 1 64 63 62 61 60 14 - 13 12 11 10 9 8 7 - 6 5 4 3 - - - 2 1 52 51 50 49 9 - 8 7 6 5 4 3 2 1 80 79 78 77 76 75 - 74 73 72 71 70 69 8 - 7 6 5 4 3 2 1 64 63 62 61 60 59 58 - 57 56 55 54 53 52 ADR_WS NC ADR_DA I2S_DA_IN1 I2S_DA_OUT I2S_WS I2S_CL I2C_DA I2C_CL NC STANDBYQ ADR_SEL D_CTR_I/O_0 D_CTR_I/O_1 NC NC NC AUD_CL_OUT TP XTAL_OUT XTAL_IN TESTEN ANA_IN2+ OUT LV LV ADR word strobe Not connected ADR data output I2S1 data input I2S data output I2S word strobe I2S clock I2C data I2C clock Not connected Stand-by (low-active) I2C Bus address select D_CTR_I/O_0 D_CTR_I/O_1 Not connected Not connected Not connected Audio clock output (18.432 MHz) Test pin Crystal oscillator Crystal oscillator Test pin IF input 2 (can be left vacant, only if IF input 1 is also not in use) OUT IN OUT IN/OUT IN/OUT IN/OUT IN/OUT LV LV LV LV LV OBL OBL LV IN IN IN/OUT IN/OUT OBL OBL LV LV LV LV LV OUT LV LV OUT IN IN IN OBL OBL OBL AVSS via 56 pF / LV AVSS via 56 pF / LV 24 59 48 68 51 ANA_IN- IN IF common (can be left vacant, only if IF input 1 is also not in use) MICRONAS INTERMETALL 49 MSP 34x1G PRELIMINARY DATA SHEET Pin No. PLCC 68-pin PSDIP 64-pin PSDIP 52-pin PQFP 80-pin PLQFP 64-pin Pin Name Type Connection (if not used) Short Description 25 26 - - - 27 - 28 - 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 - - - 44 45 46 58 57 - - - 56 - 55 - 54 53 52 51 50 49 48 47 46 45 44 43 - 42 41 - - - 40 39 38 47 46 - - - 45 - 44 - 43 42 41 - 40 39 - 38 37 - - - - 36 35 - - - 34 33 32 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 50 49 - - - 48 - 47 - 46 45 44 43 42 41 40 39 38 37 36 35 - 34 33 - - - 32 31 30 ANA_IN1+ AVSUP AVSUP NC NC AVSS AVSS MONO_IN NC VREFTOP SC1_IN_R SC1_IN_L ASG1 SC2_IN_R SC2_IN_L ASG2 SC3_IN_R SC3_IN_L ASG4 SC4_IN_R SC4_IN_L NC AGNDC AHVSS AHVSS NC NC CAPL_M AHVSUP CAPL_A IN LV OBL OBL LV LV OBL OBL IF input 1 Analog power supply 5 V Analog power supply 5 V Not connected Not connected Analog ground Analog ground Mono input Not connected Reference voltage IF A/D converter SCART 1 input, right SCART 1 input, left Analog Shield Ground 1 SCART 2 input, right SCART 2 input, left Analog Shield Ground 2 SCART 3 input, right SCART 3 input, left Analog Shield Ground 4 SCART 4 input, right SCART 4 input, left Not connected Analog reference voltage Analog ground Analog ground Not connected Not connected Volume capacitor MAIN Analog power supply 8 V Volume capacitor AUX IN LV LV OBL IN IN LV LV AHVSS IN IN LV LV AHVSS IN IN LV LV AHVSS IN IN LV LV LV or AHVSS OBL OBL OBL LV LV OBL OBL OBL 50 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Pin No. PLCC 68-pin PSDIP 64-pin PSDIP 52-pin PQFP 80-pin PLQFP 64-pin Pin Name Type Connection (if not used) Short Description 47 48 49 50 51 52 53 54 55 56 57 58 59 60 - - 61 62 63 64 65 66 - - 67 - - 68 1) Due 37 36 35 34 33 - 32 31 30 29 28 27 26 25 - - 24 23 22 21 20 19 - - 18 - - 17 31 30 29 28 27 - - 26 - 25 24 23 22 21 - - 20 - - 19 18 17 - - 16 - - 15 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 29 28 27 26 25 - 24 23 22 21 20 19 18 17 - - 16 15 14 13 12 11 - - 10 - - 9 SC1_OUT_L SC1_OUT_R VREF1 SC2_OUT_L SC2_OUT_R NC NC DACM_SUB NC DACM_L DACM_R VREF2 DACA_L DACA_R NC NC RESETQ NC NC NC I2S_DA_IN2 DVSS DVSS DVSS DVSUP DVSUP DVSUP ADR_CL OUT OUT LV LV OBL SCART output 1, left SCART output 1, right Reference ground 1 SCART output 2, left SCART output 2, right Not connected Not connected Subwoofer output Not connected Loudspeaker out, left Loudspeaker out, right Reference ground 2 Headphone out, left Headphone out, right Not connected Not connected Power-on-reset Not connected Not connected Not connected I2S2-data input Digital ground Digital ground Digital ground Digital power supply 5 V Digital power supply 5 V Digital power supply 5 V ADR clock OUT OUT LV LV LV LV OUT LV LV OUT OUT LV LV OBL OUT OUT LV LV LV LV IN OBL LV LV LV IN LV OBL OBL OBL OBL OBL OBL OUT LV to the compatibility with MSP 3410B, it is possible to connect with DVSS as well. MICRONAS INTERMETALL 51 MSP 34x1G 4.3. Pin Descriptions Pin numbers refer to the 80-pin PQFP package. Pin 1, NC - Pin not connected. Pin 2, I2C_CL - I2C Clock Input/Output (Fig. 4-12) Via this pin, the I2C-bus clock signal has to be supplied. The signal can be pulled down by the MSP in case of wait conditions. Pin 3, I2C_DA - I2C Data Input/Output (Fig. 4-12) Via this pin, the I2C-bus data is written to or read from the MSP. Pin 4, I2S_CL - I2S Clock Input/Output (Fig. 4-15) Clock line for the I2S bus. In master mode, this line is driven by the MSP; in slave mode, an external I2S clock has to be supplied. Pin 5, I2S_WS - I2S Word Strobe Input/Output (Fig. 4-15) Word strobe line for the I2S bus. In master mode, this line is driven by the MSP; in slave mode, an external I2S word strobe has to be supplied. Pin 6, I2S_DA_OUT - I2S Data Output (Fig. 4-11) Output of digital serial sound data of the MSP on the I2S bus. Pin 7, I2S_DA_IN1 - I2S Data Input 1 (Fig. 4-13) First input of digital serial sound data to the MSP via the I2S bus. Pin 8, ADR_DA - ADR Bus Data Output (Fig. 4-11) Output of digital serial data to the DRP 3510A via the ADR bus. Pin 9, ADR_WS - ADR Bus Word Strobe Output (Fig. 4-11) Word strobe output for the ADR bus. Pin 10, ADR_CL - ADR Bus Clock Output (Fig. 4-11) Clock line for the ADR bus. Pins 11, 12, 13, DVSUP* - Digital Supply Voltage Power supply for the digital circuitry of the MSP. Must be connected to a +5 V power supply. Pins 14, 15, 16, DVSS* - Digital Ground Ground connection for the digital circuitry of the MSP. Pin 17, I2S_DA_IN2 - I2S Data Input 2 (Fig. 4-13) Second input of digital serial sound data to the MSP via the I2S bus. Pins 18, 19, 20, NC - Pins not connected. Pin 21, RESETQ - Reset Input (Fig. 4-13) In the steady state, high level is required. A low level resets the MSP 34x1G. PRELIMINARY DATA SHEET Pins 22, 23, NC - Pins not connected. Pins 24, 25, DACA_R/L - Headphone Outputs (Fig. 4-21) Output of the headphone signal. A 1-nF capacitor to AHVSS must be connected to these pins. The DC offset on these pins depends on the selected headphone volume. Pin 26, VREF2 - Reference Ground 2 Reference analog ground. This pin must be connected separately to the single ground point (AHVSS). VREF2 serves as a clean ground and should be used as the reference for analog connections to the loudspeaker and headphone outputs. Pins 27, 28, DACM_R/L - Loudspeaker Outputs (Fig. 4-21) Output of the loudspeaker signal. A 1-nF capacitor to AHVSS must be connected to these pins. The DC offset on these pins depends on the selected loudspeaker volume. Pin 29, NC - Pin not connected. Pin 30, DACM_SUB - Subwoofer Output (Fig. 4-21) Output of the subwoofer signal. A 1-nF capacitor to AHVSS must be connected to this pin. Due to the low frequency content of the subwoofer output, the value of the capacitor may be increased for better suppression of high-frequency noise. The DC offset on this pin depends on the selected loudspeaker volume. Pins 31, 32 NC - Pin not connected. Pins 33, 34, SC2_OUT_R/L - SCART2 Outputs (Fig. 4-23) Output of the SCART2 signal. Connections to these pins must use a 100- series resistor and are intended to be AC-coupled. Pin 35, VREF1 - Reference Ground 1 Reference analog ground. This pin must be connected separately to the single ground point (AHVSS). VREF1 serves as a clean ground and should be used as the reference for analog connections to the SCART outputs. Pins 36, 37, SC1_OUT_R/L - SCART1 Outputs (Fig. 4-23) Output of the SCART1 signal. Connections to these pins must use a 100- series resistor and are intended to be AC-coupled. 52 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Pins 53, 54 SC2_IN_L/R - SCART2 Inputs (Fig. 4-20) The analog input signal for SCART2 is fed to this pin. Analog input connection must be AC-coupled. Pin 55, ASG1 - Analog Shield Ground 1 Analog ground (AHVSS) should be connected to this pin to reduce cross-coupling between SCART inputs. Pins 56, 57 SC1_IN_L/R - SCART1 Inputs (Fig. 4-20) The analog input signal for SCART1 is fed to this pin. Analog input connection must be AC-coupled. Pin 58, VREFTOP - Reference Voltage IF A/D Converter (Fig. 4-17) Via this pin, the reference voltage for the IF A/D converter is decoupled. It must be connected to AVSS pins with a 10-F and a 100-nF capacitor in parallel. Traces must be kept short. Pin 59, NC - Pin not connected. Pin 60 MONO_IN - Mono Input (Fig. 4-20) The analog mono input signal is fed to this pin. Analog input connection must be AC-coupled. Pins 61, 62, AVSS* - Analog Power Supply Voltage Ground connection for the analog IF input circuitry of the MSP. Pins 63, 64, NC - Pins not connected. Pin 38, CAPL_A - Volume Capacitor Headphone (Fig. 4-18) A 10-F capacitor to AHVSUP must be connected to this pin. It serves as a smoothing filter for headphone volume changes in order to suppress audible plops. The value of the capacitor can be lowered to 1-F if faster response is required. The area encircled by the trace lines should be minimized; keep traces as short as possible. This input is sensitive for magnetic induction. Pin 39, AHVSUP* - Analog Power Supply High Voltage Power is supplied via this pin for the analog circuitry of the MSP (except IF input). This pin must be connected to the +8 V supply. Pin 40, CAPL_M - Volume Capacitor Loudspeaker (Fig. 4-18) A 10-F capacitor to AHVSUP must be connected to this pin. It serves as a smoothing filter for loudspeaker volume changes in order to suppress audible plops. The value of the capacitor can be lowered to 1 F if faster response is required. The area encircled by the trace lines should be minimized; keep traces as short as possible. This input is sensitive for magnetic induction. Pins 41, 42, NC - Pins not connected. Pins 43, 44, AHVSS* - Analog Power Supply High Voltage Ground connection for the analog circuitry of the MSP (except IF input). Pin 45, AGNDC - Internal Analog Reference Voltage This pin serves as the internal ground connection for the analog circuitry (except IF input). It must be connected to the VREF pins with a 3.3-F and a 100-nF capacitor in parallel. This pins shows a DC level of typically 3.73 V. Pin 46, NC - Pin not connected. Pins 47, 48, SC4_IN_L/R - SCART4 Inputs (Fig. 4-20) The analog input signal for SCART4 is fed to this pin. Analog input connection must be AC-coupled. Pin 49, ASG4 - Analog Shield Ground 4 Analog ground (AHVSS) should be connected to this pin to reduce cross-coupling between SCART inputs. Pins 50, 51, SC3_IN_L/R - SCART3 Inputs (Fig. 4-20) The analog input signal for SCART3 is fed to this pin. Analog input connection must be AC-coupled. Pin 52, ASG2 - Analog Shield Ground 2 Analog ground (AHVSS) should be connected to this pin to reduce cross-coupling between SCART inputs. Pins 65, 66, AVSUP* - Analog Power Supply Voltage Power is supplied via this pin for the analog IF input circuitry of the MSP. This pin must be connected to the +5 V supply. Pin 67, ANA_IN1+ - IF Input 1 (Fig. 4-17) The analog sound IF signal is supplied to this pin. Inputs must be AC-coupled. This pin is designed as symmetrical input: ANA_IN1+ is internally connected to one input of a symmetrical op amp, ANA_IN- to the other. Pin 68, ANA_IN- - IF Common (Fig. 4-17) This pins serves as a common reference for ANA_IN1/ 2+ inputs. Pin 69, ANA_IN2+ - IF Input 2 (Fig. 4-17) The analog sound if signal is supplied to this pin. Inputs must be AC-coupled. This pin is designed as symmetrical input: ANA_IN2+ is internally connected to one input of a symmetrical op amp, ANA_IN- to the other. Pin 70, TESTEN - Test Enable Pin (Fig. 4-13) This pin enables factory test modes. For normal operation, it must be connected to ground. MICRONAS INTERMETALL 53 MSP 34x1G Pins 71, 72 XTAL_IN, XTAL_OUT - Crystal Input and Output Pins (Fig. 4-16) These pins are connected to an 18.432 MHz crystal oscillator which is digitally tuned by integrated shunt capacitances. An external clock can be fed into XTAL_IN. The audio clock output signal AUD_CL_OUT is derived from the oscillator. External capacitors at each crystal pin to ground (AVSS) are required. It should be verified by layout, that no supply current for the digital circuitry is flowing through the ground connection point. Pin 73, TP - This pin enables factory test modes. For normal operation, it must be left vacant. Pin 74, AUD_CL_OUT - Audio Clock Output (Fig. 4-16) This is the 18.432 MHz main clock output. Pins 75, 76, NC - Pins not connected. Pins 77, 78, D_CTR_I/O_1/0 - Digital Control Input/ Output Pins (Fig. 4-15) These pins serve as general purpose input/output pins. Pin D_CTR_I/O_1 can be used as an interrupt request pin to the controller. Pin 79, ADR_SEL - I2C Bus Address Select (Fig. 4-14) By means of this pin, one of three device addresses for the MSP can be selected. The pin can be connected to ground (I2C device addresses 80/81hex), to +5 V supply (84/85hex), or left open (88/89hex). Pin 80, STANDBYQ - Stand-by In normal operation, this pin must be High. If the MSP 34x1G is switched off by first pulling STANDBYQ low and then (after >1 s delay) switching off the 5 V, but keeping the 8-V power supply (`Stand-by'-mode), the SCART switches maintain their position and function. * Application Note: All ground pins should be connected to one low-resistive ground plane. All supply pins should be connected separately with short and low-resistive lines to the power supply. Decoupling capacitors from DVSUP to DVSS, AVSUP to AVSS, and AHVSUP to AHVSS are recommended as closely as possible to these pins. Decoupling of DVSUP and DVSS is most important. We recommend using more than one capacitor. By choosing different values, the frequency range of active decoupling can be extended. In our application boards we use: 220 pF, 470 pF, 1.5 nF, and 10 F. The capacitor with the lowest value should be placed nearest to the DVSUP and DVSS pins. PRELIMINARY DATA SHEET 54 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.4. Pin Configurations ADR_WS NC ADR_DA I2S_DA_IN1 I2S_DA_OUT I2S_WS I2S_CL I2C_DA I2C_CL ADR_CL DVSUP DVSS I2S_DA_IN2 NC NC NC RESETQ 9 NC STANDBYQ ADR_SEL D_CTR_I/O_0 D_CTR_I/O_1 NC NC NC AUD_CL_OUT TP XTAL_OUT XTAL_IN TESTEN ANA_IN2+ ANA_IN- ANA_IN1+ AVSUP 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 DACA_R DACA_L VREF2 DACM_R DACM_L NC DACM_SUB NC NC SC2_OUT_R SC2_OUT_L VREF1 SC1_OUT_R SC1_OUT_L CAPL_A AHVSUP CAPL_M MSP 34x1G 52 51 50 49 48 47 46 45 44 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 AVSS MONO_IN VREFTOP SC1_IN_R SC1_IN_L ASG1 SC2_IN_R SC2_IN_L ASG2 NC SC4_IN_L SC4_IN_R ASG4 SC3_IN_L SC3_IN_R AHVSS AGNDC Fig. 4-6: 68-pin PLCC package MICRONAS INTERMETALL 55 MSP 34x1G PRELIMINARY DATA SHEET AUD_CL_OUT NC NC D_CTR_I/O_1 D_CTR_I/O_0 ADR_SEL STANDBYQ NC I2C_CL I2C_DA I2S_CL I2S_WS I2S_DA_OUT I2S_DA_IN1 ADR_DA ADR_WS ADR_CL DVSUP DVSS I2S_DA_IN2 NC NC NC RESETQ DACA_R DACA_L VREF2 DACM_R DACM_L NC DACM_SUB NC 1 2 3 4 5 6 7 8 9 10 11 12 13 64 63 62 61 60 59 58 57 56 55 54 53 52 TP XTAL_OUT XTAL_IN TESTEN ANA_IN2+ ANA_IN- ANA_IN+ AVSUP AVSS MONO_IN VREFTOP SC1_IN_R SC1_IN_L ASG1 SC2_IN_R SC2_IN_L ASG2 SC3_IN_R SC3_IN_L ASG4 SC4_IN_R SC4_IN_L AGNDC AHVSS CAPL_M AHVSUP CAPL_A SC1_OUT_L SC1_OUT_R VREF1 SC2_OUT_L SC2_OUT_R TP AUD_CL_OUT D_CTR_I/O_1 D_CTR_I/O_0 ADR_SEL STANDBYQ I2C_CL I2C_DA I2S_CL I2S_WS I2S_DA_OUT I2S_DA_IN1 ADR_DA ADR_WS ADR_CL DVSUP DVSS I2S_DA_IN2 NC RESETQ DACA_R DACA_L VREF2 DACM_R DACM_L DACM_SUB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 52 51 50 49 48 47 46 45 44 43 XTAL_OUT XTAL_IN TESTEN ANA_IN2+ ANA_IN- ANA_IN1+ AVSUP AVSS MONO_IN VREFTOP SC1_IN_R SC1_IN_L SC2_IN_R SC2_IN_L SC3_IN_R SC3_IN_L AGNDC AHVSS CAPL_M AHVSUP CAPL_A SC1_OUT_L SC1_OUT_R VREF1 SC2_OUT_L SC2_OUT_R MSP 34x1G 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 MSP 34x1G 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 Fig. 4-8: 52-pin PSDIP package Fig. 4-7: 64-pin PSDIP package 56 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G SC2_IN_L SC2_IN_R ASG1 SC1_IN_L SC1_IN_R VREFTOP NC MONO_IN AVSS AVSS NC NC ASG2 SC3_IN_R SC3_IN_L ASG4 SC4_IN_R SC4_IN_L NC AGNDC AHVSS AHVSS NC NC AVSUP AVSUP ANA_IN1+ ANA_IN- ANA_IN2+ TESTEN XTAL_IN XTAL_OUT TP AUD_CL_OUT NC NC D_CTR_I/O_1 D_CTR_I/O_0 ADR_SEL STANDBYQ 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 65 40 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 1 2 3 4 5 6 7 8 9 39 38 37 36 35 34 CAPL_M AHVSUP CAPL_A SC1_OUT_L SC1_OUT_R VREF1 SC2_OUT_L SC2_OUT_R NC NC DACM_SUB NC DACM_L DACM_R VREF2 DACA_L MSP 34x1G 33 32 31 30 29 28 27 26 25 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 NC I2C_CL I2C_DA I2S_CL I2S_WS I2S_DA_OUT I2S_DA_IN1 ADR_DA ADR_WS ADR_CL DVSUP DVSUP NC I2S_DA_IN2 DVSS DVSS DVSS DVSUP NC NC NC RESETQ NC DACA_R Fig. 4-9: 80-pin PQFP package MICRONAS INTERMETALL 57 MSP 34x1G PRELIMINARY DATA SHEET SC2_IN_L SC2_IN_R ASG1 SC1_IN_L SC1_IN_R VREFTOP MONO_IN AVSS ASG2 SC3_IN_R SC3_IN_L ASG4 SC4_IN_R SC4_IN_L AGNDC AHVSS 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 AVSUP ANA_IN1+ ANA_IN- ANA_IN2+ TESTEN XTAL_IN XTAL_OUT TP AUD_CL_OUT NC NC D_CTR_I/OUT1 D_CTR_I/OUT0 ADR_SEL STANDBYQ NC 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 1 I2C_CL I2C_DA I2S_CL I2S_WS I2S_DA_OUT I2S_DA_IN1 ADR_DA ADR_WS NC I2S_DA_IN2 DVSS DVSUP ADR_CL NC NC 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RESETQ 32 31 30 29 28 27 26 CAPL_M AHVSUP CAPL_A SC1_OUT_L SC1_OUT_R VREF1 SC2_OUT_L SC2_OUT_R NC DACM_SUB NC DACM_L DACM_R VREF2 DACA_L DACA_R MSP 34x1G 25 24 23 22 21 20 19 18 17 Fig. 4-10: 64-pin PLQFP package 58 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.5. Pin Circuits Pin numbers refer to the PQFP80 package. DVSUP P N GND Fig. 4-11: Output Pins 6, 8, 9, and 10 (I2S_DA_OUT, ADR_DA, ADR_WS, ADR_CL) P N GND Fig. 4-15: Input/Output Pins 4, 5, 77, and 78 (I2S_CL, I2S_WS, D_CTR_I/O_1, D_CTR_I/O_0) DVSUP P N GND Fig. 4-12: Input/Output Pins 2 and 3 (I2C_CL, I2C_DA) 3-30 pF 500 k N 2.5 V 3-30 pF Fig. 4-16: Output/Input Pins 71, 72, and 74 (XTAL_IN, XTAL_OUT, AUD_CL_OUT) Fig. 4-13: Input Pins 7, 17, 21, 70, and 80 (I2S_DA_IN1, I2S_DA_IN2, RESETQ, TESTEN, STANDBYQ) ANA_IN1+ ANA_IN2+ DVSUP 23 k A D ANA_IN- VREFTOP 23 k GND ADR_SEL Fig. 4-14: Input Pin 79 (ADR_SEL) Fig. 4-17: Input Pins 58, 67, 68, and 69 (VREFTOP, ANA_IN1+, ANA_IN-, ANA_IN2+) MICRONAS INTERMETALL 59 MSP 34x1G PRELIMINARY DATA SHEET 125 k 0...2 V 3.75 V Fig. 4-18: Capacitor Pins 38 and 40 (CAPL_A, CAPL_M) Fig. 4-22: Pin 45 (AGNDC) 26 pF 24 k 3.75 V 120 k Fig. 4-19: Input Pin 60 (MONO_IN) 3.75 V 300 40 k 3.75 V Fig. 4-23: Output Pins 33, 34, 36, and 37 (SC_2_OUT_R/L, SC_1_OUT_R/L) Fig. 4-20: Input Pins 47, 48, 50, 51, 53, 54, 56, and 57 (SC4-1_IN_L/R) AHVSUP 0...1.2 mA 3.3 k Fig. 4-21: Output Pins 24, 25, 27, 28 and 30 (DACA_R/L, DACM_R/L, DACM_SUB) 60 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.6. Electrical Characteristics 4.6.1. Absolute Maximum Ratings Symbol TA TS VSUP1 VSUP2 VSUP3 dVSUP23 PTOT Parameter Ambient Operating Temperature Storage Temperature First Supply Voltage Second Supply Voltage Third Supply Voltage Voltage between AVSUP and DVSUP Power Dissipation PLCC68 PSDIP64 PSDIP52 PQFP80 PLQFP64 Input Voltage, all Digital Inputs Input Current, all Digital Pins Input Voltage, all Analog Inputs Input Current, all Analog Inputs Output Current, all SCART Outputs Output Current, all Analog Outputs except SCART Outputs Output Current, other pins connected to capacitors - SCn_IN_s,3) MONO_IN SCn_IN_s,3) MONO_IN SCn_OUT_s3) DACp_s3) CAPL_p,3) AGNDC Pin Name - - AHVSUP DVSUP AVSUP AVSUP, DVSUP AHVSUP, DVSUP, AVSUP Min. 0 -40 -0.3 -0.3 -0.3 -0.5 Max. 701) 125 9.0 6.0 6.0 0.5 Unit C C V V V V 1200 1300 1200 1000 9601) -0.3 -20 -0.3 -5 4), 5) 4) mW mW mW mW mW V mA2) V mA2) VIdig IIdig VIana IIana IOana IOana ICana 1) 2) 3) 4) 5) VSUP2+0.3 +20 VSUP1+0.3 +5 4), 5) 4) 4) 4) PLQFP64: 65 C positive value means current flowing into the circuit "n" means "1", "2", "3", or "4", "s" means "L" or "R", "p" means "M" or "A" The analog outputs are short-circuit proof with respect to First Supply Voltage and ground. Total chip power dissipation must not exceed absolute maximum rating. Stresses beyond those listed in the "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or any other conditions beyond those indicated in the "Recommended Operating Conditions/Characteristics" of this specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. MICRONAS INTERMETALL 61 MSP 34x1G 4.6.2. Recommended Operating Conditions (TA = 0 to 70 C) 4.6.2.1. General Recommended Operating Conditions Symbol VSUP1 Parameter First Supply Voltage (8-V Operation) First Supply Voltage (5-V Operation) VSUP2 VSUP3 tSTBYQ1 Second Supply Voltage Third Supply Voltage STANDBYQ Setup Time before Turn-off of Second Supply Voltage DVSUP AVSUP STANDBYQ, DVSUP Pin Name AHVSUP Min. 7.6 4.75 4.75 4.75 1 PRELIMINARY DATA SHEET Typ. 8.0 5.0 5.0 5.0 Max. 8.7 5.25 5.25 5.25 Unit V V V V s 4.6.2.2. Analog Input and Output Recommendations Symbol CAGNDC Parameter AGNDC-Filter-Capacitor Ceramic Capacitor in Parallel CinSC VinSC VinMONO RLSC CLSC CVMA CFMA 1) Pin Name AGNDC Min. -20% -20% Typ. 3.3 100 330 Max. Unit F nF nF DC-Decoupling Capacitor in front of SCART Inputs SCART Input Level Input Level, Mono Input SCART Load Resistance SCART Load Capacitance Main/AUX Volume Capacitor Main/AUX Filter Capacitor SCn_IN_s1) -20% 2.0 MONO_IN SCn_OUT_s1) 10 6.0 CAPL_M, CAPL_A DACM_s, DACA_s1) -10% 10 1 +10% 2.0 VRMS VRMS k nF F nF "n" means "1", "2", or "3", "s" means "L" or "R", "p" means "M" or "A" 62 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.6.2.3. Recommendations for Analog Sound IF Input Signal Symbol CVREFTOP Parameter VREFTOP-Filter-Capacitor Ceramic Capacitor in Parallel FIF_FMTV FIF_FMRADIO VIF_FM VIF_AM RFMNI Analog Input Frequency Range for TV Applications Analog Input Frequency for FM-Radio Applications Analog Input Range FM/NICAM Analog Input Range AM/NICAM Ratio: NICAM Carrier/FM Carrier (unmodulated carriers) BG: I: Ratio: NICAM Carrier/AM Carrier (unmodulated carriers) Ratio: FM-Main/FM-Sub Satellite Ratio: FM1/FM2 German FM-System Ratio: Main FM Carrier/ Color Carrier Ratio: Main FM Carrier/ Luma Components Passband Ripple Suppression of Spectrum above 9.0 MHz (not for FM Radio) Maximum FM-Deviation (approx.) normal mode HDEV2: high deviation mode HDEV3: very high deviation mode 15 15 - 15 0.1 0.1 ANA_IN1+, ANA_IN2+, ANA_IN- Pin Name VREFTOP Min. -20 % -20 % 0 10.7 0.8 0.45 3 0.8 Typ. 10 100 9 Max. Unit F nF MHz MHz Vpp Vpp -20 -23 -25 -7 -10 -11 7 7 - - - 0 0 0 dB dB dB dB dB RAMNI RFM RFM1/FM2 RFC RFV PRIF SUPHF FMMAX - - 2 - dB dB dB dB 180 360 540 kHz kHz kHz MICRONAS INTERMETALL 63 MSP 34x1G 4.6.2.4. Crystal Recommendations Symbol Parameter Pin Name Min. PRELIMINARY DATA SHEET Typ. Max. Unit General Crystal Recommendations fP RR C0 CL Crystal Parallel Resonance Frequency at 12 pF Load Capacitance Crystal Series Resistance Crystal Shunt (Parallel) Capacitance External Load Capacitance1) XTAL_IN, XTAL_OUT 18.432 8 6.2 25 7.0 MHz pF pF pF pF PSDIP approx. 1.5 PLCC approx. 3.3 P(L)QFP approx. 3.3 Crystal Recommendations for Master-Slave Applications (MSP-clock must perform synchronization to I2S clock) fTOL DTEM C1 fCL Accuracy of Adjustment Frequency Variation versus Temperature Motional (Dynamic) Capacitance Required Open Loop Clock Frequency (Tamb = 25 C) AUD_CL_OUT -20 -20 19 18.431 24 18.433 +20 +20 ppm ppm fF MHz Crystal Recommendations for FM / NICAM Applications (No MSP-clock synchronization to I2S clock possible) fTOL DTEM C1 fCL Accuracy of Adjustment Frequency Variation versus Temperature Motional (Dynamic) Capacitance Required Open Loop Clock Frequency (Tamb = 25 C) AUD_CL_OUT -30 -30 15 18.4305 18.4335 +30 +30 ppm ppm fF MHz Crystal Recommendations for all analog FM/AM Applications (No MSP-clock synchronization to I2S clock possible) fTOL DTEM fCL Accuracy of Adjustment Frequency Variation versus Temperature Required Open Loop Clock Frequency (Tamb = 25 C) AUD_CL_OUT -100 -50 18.429 +100 +50 18.435 ppm ppm MHz Amplitude Recommendation for Operation with External Clock Input (Cload after reset typ. 22 pF) VXCA 1)External External Clock Amplitude XTAL_IN 0.7 Vpp capacitors at each crystal pin to ground are required. They are necessary to tune the open-loop frequency of the internal PLL and to stabilize the frequency in closed-loop operation. Due to different layouts, the accurate capacitor size should be determined with the customer PCB. The suggested values (1.5...3.3 pF) are figures based on experience and should serve as "start value". To define the capacitor size, reset the MSP without transmitting any further I2C telegrams. Measure the frequency at AUD_CL_OUT-pin. Change the capacitor size until the free running frequency matches 18.432 MHz as closely as possible. The higher the capacity, the lower the resulting clock frequency. 64 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.6.3. Characteristics at TA = 0 to 70 C, fCLOCK = 18.432 MHz, VSUP1 = 7.6 to 8.7 V, VSUP2 = 4.75 to 5.25 V for min./max. values at TA = 60 C, fCLOCK = 18.432 MHz, VSUP1 = 8 V, VSUP2 = 5 V for typical values, TJ = Junction Temperature MAIN (M) = Loudspeaker Channel, AUX (A) = Headphone Channel 4.6.3.1. General Characteristics Symbol Supply ISUP1A First Supply Current (active) (8-V Operation) Analog Volume for Main and Aux at 0 dB Analog Volume for Main and Aux at -30 dB Parameter Pin Name Min. Typ. Max. Unit Test Conditions AHVSUP 9.6 6.3 17.1 11.2 24.6 16.1 mA mA First Supply Current (active) (5-V Operation) Analog Volume for Main and Aux at 0 dB Analog Volume for Main and Aux at -30 dB 6.4 4.2 DVSUP AVSUP AHVSUP 50 20 3.5 11.4 7.5 65 35 5.6 16.4 10.7 85 45 7.7 mA mA mA mA mA STANDBYQ = low ISUP2A ISUP3A ISUP1S Second Supply Current (active) Third Supply Current (active) First Supply Current (8-V Operation) (standby mode) at Tj = 27 C First Supply Current (5-V Operation) (standby mode) at Tj = 27 C 2.3 3.7 5.1 mA STANDBYQ = low Clock fCLOCK DCLOCK tJITTER VxtalDC tStartup VACLKAC VACLKDC routHF_ACL Clock Input Frequency Clock High to Low Ratio Clock Jitter (Verification not provided in Production Test) DC-Voltage Oscillator Oscillator Startup Time at VDD Slew-rate of 1 V/1 s Audio Clock Output AC Voltage Audio Clock Output DC Voltage HF Output Resistance XTAL_IN, XTAL_OUT AUD_CL_OUT 1.2 0.4 140 2.5 0.4 2 XTAL_IN 45 18.432 55 50 MHz % ps V ms 1.8 0.6 Vpp VSUP3 load = 40 pF Imax = 0.2 mA MICRONAS INTERMETALL 65 MSP 34x1G 4.6.3.2. Digital Inputs, Digital Outputs Symbol Parameter Pin Name Min. Typ. Max. PRELIMINARY DATA SHEET Unit Test Conditions Digital Input Levels VDIGIL VDIGIH ZDIGI IDLEAK VDIGIL VDIGIH IADRSEL Digital Input Low Voltage Digital Input High Voltage Input Impedance Digital Input Leakage Current -1 STANDBYQ D_CTR_I/O_0/1 0.5 5 1 0.2 VSUP2 VSUP2 pF A 0 V < UINPUT< DVSUP D_CTR_I/O_0/1: tri-state Digital Input Low Voltage Digital Input High Voltage Input Current Address Select Pin ADR_SEL 0.8 -500 -220 220 0.2 VSUP2 VSUP2 A UADR_SEL= DVSS UADR_SEL= DVSUP 500 A Digital Output Levels VDCTROL VDCTROH Digital Output Low Voltage Digital Output High Voltage D_CTR_I/O_0 D_CTR_I/O_1 4.0 0.4 V V IDDCTR = 1 mA IDDCTR = -1 mA 66 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.6.3.3. Reset Input and Power-Up Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions RESETQ Input Levels VRHL VRLH ZRES IRES Reset High-Low Transition Voltage Reset Low-High Transition Voltage Input Impedance Input Pin Leakage Current -1 RESETQ 0.45 0.7 0.55 0.8 5 1 VSUP2 VSUP2 pF A 0 V < UINPUT< DVSUP DVSUP AVSUP 4.5V t/ms RESETQ 0.7x DVSUP Low-to-High Threshold 0.45...0.55x DVSUP High-to-Low Threshold Note: The reset should not reach high level before the oscillator has started. This requires a reset delay of >2 ms 0.7 x DVSUP means 3.5 Volt with DVSUP = 5.0 V t/ms Reset Delay >2 ms Internal Reset High Low t/ms Fig. 4-24: Power-up sequence MICRONAS INTERMETALL 67 MSP 34x1G 4.6.3.4. I2C-Bus Characteristics Symbol VI2CIL VI2CIH tI2C1 tI2C2 tI2C5 tI2C6 tI2C3 tI2C4 fI2C VI2COL II2COH tI2COL1 tI2COL2 Parameter I2C-Bus Input Low Voltage I2C-Bus Input High Voltage I2C Start Condition Setup Time I C Stop Condition Setup Time I2C-Data Setup Time before Rising Edge of Clock I2C-Data Hold Time after Falling Edge of Clock I2C-Clock Low Pulse Time I2C-Clock High Pulse Time I2C-BUS Frequency I C-Data Output Low Voltage I2C-Data Output High Leakage Current I2C-Data Output Hold Time after Falling Edge of Clock I2C-Data Output Setup Time before Rising Edge of Clock 15 2 2 PRELIMINARY DATA SHEET Pin Name I2C_CL, I2C_DA Min. Typ. Max. 0.3 Unit VSUP2 VSUP2 ns ns ns Test Conditions 0.6 120 120 55 55 ns I2C_CL 500 500 1.0 ns ns MHz V A II2COL = 3 mA VI2COH = 5 V I2C_CL, I2C_DA 0.4 1.0 ns 100 ns fI2C = 1 MHz 1/FI2C I2C_CL TI2C4 TI2C3 TI2C1 I2C_DA as input TI2C5 TI2C6 TI2C2 TI2COL2 I2C_DA as output TI2COL1 Fig. 4-25: I2C bus timing diagram 68 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.6.3.5. I2S-Bus Characteristics Symbol VI2SIL VI2SIH ZI2SI IDLEAKI2SI tI2S1 tI2S2 fI2SWS fI2SCL RI2SCL tI2SWS1 Parameter Input Low Voltage Input High Voltage Input Impedance Input Leakage Current I2S-Data Input Setup Time before Rising Edge of Clock I2S-Data Input Hold Time after Falling Edge of Clock I2S-Word Strobe Input Frequency when MSP in I2S-Slave Mode I2S-Clock Input Frequency when MSP in I2S-Slave-Mode I2S-Clock Input Ratio when MSP in I2S-Slave-Mode I2S-Word Strobe Input Setup Time before Rising Edge of Clock when MSP in I2S-Slave-Mode I2S-Word Strobe Input Hold Time after Falling Edge of Clock when MSP in I2S-Slave-Mode I2S Output Low Voltage I2S Output High Voltage I2S-Word Strobe Output Frequency I2S-Clock Output Frequency I2S-Clock High/Low-Ratio I2S-Data Setup Time before Rising Edge of Clock I2S-Data Hold Time after Falling Edge of Clock I2S-Word Strobe Setup Time before Rising Edge of Clock I2S-Word Strobe Hold Time after Falling Edge of Clock I2S_CL, I2S_WS 200 I2S_CL, I2S_DA_OUT I2S_WS, I2S_CL, I2S_DA_OUT I2S_WS I2S_CL 0.9 200 I2S_WS, I2S_CL I2S_WS -1 Pin Name I2S_DA_IN1/2 I2S_CL I2S_WS Min. Typ. Max. 0.2 0.5 5 1 Unit VSUP2 VSUP2 pF A 0 V < UINPUT< DVSUP I2S slave mode Test Conditions I2S_DA_IN1/2, I2S_CL 20 ns 0 ns 32.0 kHz I2S_CL 1.024 MHz 0.9 1.1 60 ns tI2SWS2 0 ns VI2SOL VI2SOH fI2SWS fI2SCL tI2S1/I2S2 tI2S3 tI2S4 tI2S5 tI2S6 0.4 4.0 32.0 1024 1.0 1.1 V V kHz kHz II2SOL = 1 mA II2SOH = -1 mA NICAM-PLL closed ns CL = 30 pF 180 ns ns 180 ns MICRONAS INTERMETALL 69 MSP 34x1G (Data: MSB first) FI2SWS I2S_WS PRELIMINARY DATA SHEET SONY Mode PHILIPS Mode PHILIPS/SONY Mode programmable by MODUS[6] I2S_CL Detail A I2S_DAIN R LSB L MSB SONY Mode PHILIPS Mode Detail C L LSB R MSB R LSB L LSB 16 bit left channel Detail B I2S_DAOUT R LSB L MSB L LSB R MSB 16 bit right channel R LSB L LSB 16 bit left channel 16 bit right channel Detail C I2S_CL FI2SCL Detail A,B I2S_CL TI2SWS1 TI2SWS2 TI2S1 TI2S2 I2S_WS as INPUT TI2S5 TI2S6 I2S_DA_IN TI2S3 TI2S4 I2S_WS as OUTPUT I2S_DA_OUT Fig. 4-26: I2S bus timing diagram 4.6.3.6. Analog Baseband Inputs and Outputs, AGNDC Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions Analog Ground VAGNDC0 AGNDC Open Circuit Voltage (8-V Operation) AGNDC Open Circuit Voltage (5-V Operation) RoutAGN AGNDC Output Resistance (8-V Operation) AGNDC Output Resistance (5-V Operation) Analog Input Resistance RinSC RinMONO 1) AGNDC 3.67 3.77 3.87 V Rload 10 M 2.41 2.51 2.61 V 3 V VAGNDC 4 V 70 125 180 k 47 83 120 k SCART Input Resistance from TA = 0 to 70 C MONO Input Resistance from TA = 0 to 70 C SCn_IN_s1) 25 40 58 k fsignal = 1 kHz, I = 0.05 mA fsignal = 1 kHz, I = 0.1 mA MONO_IN 15 24 35 k "n" means "1", "2", "3", or "4"; "s" means "L" or "R" 70 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions Audio Analog-to-Digital-Converter VAICL Effective Analog Input Clipping Level for Analog-to-DigitalConversion (8-V Operation) Effective Analog Input Clipping Level for Analog-to-DigitalConversion (5-V Operation) SCART Outputs RoutSC SCART Output Resistance at Tj = 27 C from TA = 0 to 70 C Deviation of DC-Level at SCART Output from AGNDC Voltage Gain from Analog Input to SCART Output Frequency Response from Analog Input to SCART Output Bandwidth: 0 to 20000 Hz Effective Signal Level at SCART-Output during full-scale Digital Input Signal from I2S (8-V Operation) Effective Signal Level at SCART-Output during full-scale Digital Input Signal from I2S (5-V Operation) Main and AUX Outputs RoutMA Main/AUX Output Resistance at Tj = 27 C from TA = 0 to 70 C DC-Level at Main/AUX-Output for Analog Volume at 0 dB for Analog Volume at -30 dB (8-V Operation) DC-Level at Main/AUX-Output for Analog Volume at 0 dB for Analog Volume at -30 dB (5-V Operation) VoutMA Effective Signal Level at Main/ AUX-Output during full-scale Digital Input Signal from I2S for Analog Volume at 0 dB (8-V Operation) Effective Signal Level at Main/ AUX-Output during full-scale Digital Input Signal from I2S for Analog Volume at 0 dB (5-V Operation) 1) SCn_IN_s,1) MONO_IN 2.00 2.25 VRMS fsignal = 1 kHz 1.13 1.51 VRMS SCn_OUT_s1) 200 200 -70 SCn_IN_s,1) MONO_IN SCn_OUT_s1) -1.0 -0.5 330 460 500 +70 +0.5 +0.5 mV fsignal = 1 kHz, I = 0.1 mA dVOUTSC ASCtoSC frSCtoSC dB fsignal = 1 kHz with resp. to 1 kHz dB VoutSC SCn_OUT_s1) 1.8 1.9 2.0 VRMS fsignal = 1 kHz 1.17 1.27 1.37 VRMS DACp_s1) 2.1 2.1 3.3 4.6 5.0 k k fsignal = 1 kHz, I = 0.1 mA VoutDCMA 1.80 2.04 61 2.28 V mV 1.12 1.36 40 1.60 V mV 1.23 1.37 1.51 VRMS fsignal = 1 kHz 0.76 0.90 1.04 VRMS "n" means "1", "2", "3", or "4"; "s" means "L" or "R"; "p" means "M" or "A" MICRONAS INTERMETALL 71 MSP 34x1G 4.6.3.7. Sound IF Inputs Symbol RIFIN Parameter Input Impedance Pin Name ANA_IN1+, ANA_IN2+, ANA_IN- VREFTOP ANA_IN1+, ANA_IN2+, ANA_IN- ANA_IN1+, ANA_IN2+, ANA_IN- Min. 1.5 6.8 Typ. 2 9.1 Max. 2.5 11.4 PRELIMINARY DATA SHEET Unit k k Test Conditions Gain AGC = 20 dB Gain AGC = 3 dB DCVREFTOP DCANA_IN DC Voltage at VREFTOP DC Voltage on IF Inputs 2.45 1.3 2.65 1.5 2.75 1.7 V V XTALKIF BWIF AGC Crosstalk Attenuation 3 dB Bandwidth AGC Step Width 40 10 0.85 dB MHz dB fsignal = 1 MHz Input Level = -2 dBr 4.6.3.8. Power Supply Rejection Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions PSRR: Rejection of Noise on AHVSUP at 1 kHz PSRR AGNDC From Analog Input to I2S Output AGNDC MONO_IN, SCn_IN_s1) MONO_IN, SCn_IN_s1) SCn_OUT_s1) SCn_OUT_s1) DACp_s1) 80 70 dB dB From Analog Input to SCART Output From I2S Input to SCART Output From I2S Input to MAIN or AUX Output 1) 70 dB 60 80 dB dB "n" means "1", "2", "3", or "4"; "s" means "L" or "R"; "p" means "M" or "A" 72 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 4.6.3.9. Analog Performance Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions Specifications for 8-V Operation SNR Signal-to-Noise Ratio from Analog Input to I2S Output MONO_IN, SCn_IN_s1) 85 88 dB Input Level = -20 dB with resp. to VAICL, fsig = 1 kHz, equally weighted 20 Hz...16 kHz Input Level = -20 dB, fsig = 1 kHz, equally weighted 20 Hz...20 kHz Input Level = -20 dB, fsig = 1 kHz, equally weighted 20 Hz...15 kHz Input Level = -20 dB, fsig = 1 kHz, equally weighted 20 Hz...15 kHz from Analog Input to SCART Output MONO_IN, SCn_IN_s1) SCn_OUT_s1) SCn_OUT_s1) 93 96 dB from I2S Input to SCART Output 85 88 dB from I2S Input to Main/AUX-Output for Analog Volume at 0 dB for Analog Volume at -30 dB DACp_s1) 85 78 88 83 dB dB THD Total Harmonic Distortion from Analog Input to I2S Output MONO_IN, SCn_IN_s1) 0.01 0.03 % Input Level = -3 dBr with resp. to VAICL, fsig = 1 kHz, equally weighted 20 Hz...16 kHz Input Level = -3 dBr, fsig = 1 kHz, equally weighted 20 Hz...20 kHz Input Level = -3 dBr, fsig = 1 kHz, equally weighted 20 Hz...16 kHz Input Level = -3 dBr, fsig = 1 kHz, equally weighted 20 Hz...16 kHz from Analog Input to SCART Output MONO_IN, SCn_IN_s SCn_OUT_s1) SCn_OUT_s1) 0.01 0.03 % from I2S Input to SCART Output 0.01 0.03 % from I2S Input to Main or AUX Output DACA_s, DACM_s1) 0.01 0.03 % 1) "n" means "1", "2", "3", or "4"; "s" means "L" or "R"; "p" means "M" or "A" MICRONAS INTERMETALL 73 MSP 34x1G PRELIMINARY DATA SHEET Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions Specifications for 5-V Operation SNR Signal-to-Noise Ratio from Analog Input to I2S Output MONO_IN, SCn_IN_s1) 82 85 dB Input Level = -20 dB with resp. to VAICL, fsig = 1 kHz, equally weighted 20 Hz...16 kHz Input Level = -20 dB, fsig = 1 kHz, equally weighted 20 Hz...20 kHz Input Level = -20 dB, fsig = 1 kHz, equally weighted 20 Hz...15 kHz Input Level = -20 dB, fsig = 1 kHz, equally weighted 20 Hz...15 kHz from Analog Input to SCART Output MONO_IN, SCn_IN_s1) SCn_OUT_s1) SCn_OUT_s1) 90 93 dB from I2S Input to SCART Output 82 85 dB from I2S Input to Main/AUX-Output for Analog Volume at 0 dB for Analog Volume at -30 dB DACp_s1) 82 75 85 80 dB dB THD Total Harmonic Distortion from Analog Input to I2S Output MONO_IN, SCn_IN_s1) 0.03 0.1 % Input Level = -3 dBr with resp. to VAICL, fsig = 1 kHz, equally weighted 20 Hz...16 kHz Input Level = -3 dBr, fsig = 1 kHz, equally weighted 20 Hz...20 kHz Input Level = -3 dBr, fsig = 1 kHz, equally weighted 20 Hz...16 kHz Input Level = -3 dBr, fsig = 1 kHz, equally weighted 20 Hz...16 kHz from Analog Input to SCART Output MONO_IN, SCn_IN_s SCn_OUT_s1) SCn_OUT_s1) 0.1 % from I2S Input to SCART Output 0.1 % from I2S Input to Main or AUX Output DACA_s, DACM_s1) 0.1 % 1) "n" means "1", "2", "3", or "4"; "s" means "L" or "R"; "p" means "M" or "A" 74 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions XTALK Specifications for 8-V and 5-V Operation XTALK Crosstalk Attenuation - PLCC68 - PSDIP64 Input Level = -3 dB, fsig = 1 kHz, unused analog inputs connected to ground by Z < 1 k equally weighted 20 Hz...20 kHz PLCC68 PSDIP64 PLCC68 PSDIP64 PLCC68 PSDIP64 PLCC68 PSDIP64 80 80 80 80 80 80 80 80 dB dB dB dB dB dB dB dB equally weighted 20 Hz...16 kHz PLCC68 PSDIP64 80 75 dB dB (equally weighted 20 Hz...20 kHz same signal source on left and right disturbing channel, effect on each observed output channel between left and right channel within SCART Input/Output pair (LR, RL) SCn_IN SCn_OUT1) SC1_IN or SC2_IN I2S Output SC3_IN I2S Output I2S Input SCn_OUT1) between left and right channel within Main or AUX Output pair I2S Input DACp1) between SCART Input/Output pairs D = disturbing program O = observed program D: MONO/SCn_IN SCn_OUT O: MONO/SCn_IN SCn_OUT1) D: MONO/SCn_IN SCn_OUT or unsel. O: MONO/SCn_IN I2S Output D: MONO/SCn_IN SCn_OUT O: I2S Input SCn_OUT1) D: MONO/SCn_IN unselected O: I2S Input SC1_OUT1) PLCC68 PSDIP64 PLCC68 PSDIP64 PLCC68 PSDIP64 PLCC68 PSDIP64 100 100 100 95 100 100 100 100 dB dB dB dB dB dB dB dB Crosstalk between Main and AUX Output pairs I2S Input DACp1) PLCC68 PSDIP64 95 90 dB dB (equally weighted 20 Hz...16 kHz) same signal source on left and right disturbing channel, effect on each observed output channel (equally weighted 20 Hz...20 kHz) same signal source on left and right disturbing channel, effect on each observed output channel XTALK Crosstalk from Main or AUX Output to SCART Output and vice versa D = disturbing program O = observed program D: MONO/SCn_IN/DSP SCn_OUT O: I2S Input DACp1) D: MONO/SCn_IN/DSP SCn_OUT O: I2S Input DACp1) D: I2S Input DACp O: MONO/SCn_IN SCn_OUT1) D: I2S Input DACM O: I2S Input SCn_OUT1) PLCC68 PSDIP64 PLCC68 PSDIP64 PLCC68 PSDIP64 PLCC68 PSDIP64 85 80 90 85 100 95 100 95 dB dB dB dB dB dB dB dB SCART output load resistance 10 k SCART output load resistance 30 k 1) "n" means "1", "2", "3", or "4"; "s" means "L" or "R"; "p" means "M" or "A" MICRONAS INTERMETALL 75 MSP 34x1G 4.6.3.10. Sound Standard Dependent Characteristics Symbol Parameter Pin Name Min. Typ. Max. PRELIMINARY DATA SHEET Unit Test Conditions NICAM Characteristics (MSP Standard Code = 8) dVNICAMOUT S/NNICAM Tolerance of Output Voltage of NICAM Baseband Signal S/N of NICAM Baseband Signal DACp_s, SCn_OUT_s1) -1.5 +1.5 dB 2.12 kHz, Modulator input level = 0 dBref NICAM: -6 dB, 1 kHz, RMS unweighted 0 to 15 kHz, Vol = 9 dB NIC_Presc = 7Fhex Output level 1 VRMS at DACp_s 2.12 kHz, Modulator input level = 0 dBref FM+NICAM, norm conditions Modulator input level = -12 dB dBref; RMS 72 dB THDNICAM BERNICAM fRNICAM XTALKNICAM SEPNICAM Total Harmonic Distortion + Noise of NICAM Baseband Signal NICAM: Bit Error Rate NICAM Frequency Response , 20...15000 Hz NICAM Crosstalk Attenuation (Dual) NICAM Channel Separation (Stereo) -1.0 0.1 % 10-7 dB 1 +1.0 80 80 dB dB FM Characteristics (MSP Standard Code = 3) dVFMOUT S/NFM THDFM Tolerance of Output Voltage of FM Demodulated Signal S/N of FM Demodulated Signal Total Harmonic Distortion + Noise of FM Demodulated Signal DACp_s, SCn_OUT_s1) -1.5 +1.5 dB 1 FM-carrier, 50 s, 1 kHz, 40 kHz deviation; RMS 1 FM-carrier 5.5 MHz, 50 s, 1 kHz, 40 kHz deviation; RMS, unweighted 0 to 15 kHz (for S/N); full input range, FM-Prescale = 46hex, Vol = 0 dB Output Level 1 VRMS at DACp_s 1 FM-carrier 5.5 MHz, 50 s, Modulator input level = -14.6 dBref; RMS 2 FM-carriers 5.5/5.74 MHz, 50 s, 1 kHz, 40 kHz deviation; Bandpass 1 kHz 2 FM-carriers 5.5/5.74 MHz, 50 s, 1 kHz, 40 kHz deviation; RMS 73 0.1 dB % fRFM FM Frequency Response 20...15000 Hz -1.0 +1.0 dB XTALKFM FM Crosstalk Attenuation (Dual) 80 dB SEPFM FM Channel Separation (Stereo) DACp_s, SCn_OUT_s1) 50 dB AM Characteristics (MSP Standard Code = 9) S/NAM(1) S/N of AM Demodulated Signal measurement condition: RMS/Flat MSP 34x1G Version A1 MSP 34x1G Version A2 and later S/N of AM Demodulated Signal measurement condition: QP/CCIR MSP 34x1G Version A1 MSP 34x1G Version A2 and later Total Harmonic Distortion + Noise of AM Demodulated Signal MSP 34x1G Version A1 MSP 34x1G Version A2 and later RM Frequency Response 50...12000 Hz "s" means "L" or "R"; -2.5 DACp_s, SCn_OUT_s1) 44 55 dB dB SIF level: 0.1-0.8 Vpp AM-carrier 54% at 6.5 MHz Vol = 0 dB, FM/AM prescaler set for output = 0.5 VRMS at Loudspeaker out; Standard Code = 09hex no video/chroma components S/NAM(2) 35 45 dB dB THDAM 0.8 0.6 +1.0 % % dB fRRM 1) "n" means "1", "2", "3", or "4"; "p" means "Loudspeaker (Main)'' or ``Headphone (AUX)'' 76 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions BTSC Characteristics (MSP Standard Code = 20hex, 21hex) S/NBTSC S/N of BTSC Stereo Signal S/N of BTSC-SAP Signal DACp_s, SCn_OUT_s1) 68 57 dB dB 1 kHz L or R or SAP, 100% modulation, 75 s deemphasis, RMS unweighted 0 to 15 kHz 1 kHz L or R or SAP, 100% 75 s EIM2), DBX NR, RMS unweighted 0 to 15 kHz L or R or SAP, 1%...66% EIM2), DBX NR THDBTSC THD+N of BTSC Stereo Signal THD+N of BTSC SAP Signal 0.1 0.5 % % fRBTSC Frequency Response of BTSC Stereo, 50 Hz...12 kHz Frequency Response of BTSCSAP, 50 Hz...9 kHz -0.5 -1.0 0.5 0.6 dB dB XTALKBTSC Stereo SAP SAP Stereo 76 80 dB dB 1 kHz L or R or SAP, 100% modulation, 75 s deemphasis, Bandpass 1 kHz L or R 1%...66% EIM2), DBX NR SEPBTSC Stereo Separation 50 Hz...10 kHz 50 Hz...12 kHz Pilot deviation threshold Stereo off on Stereo on off ANA_IN1+, ANA_IN2+ 35 30 dB dB FMpil 3.2 1.2 3.5 1.5 15.843 kHz kHz kHz 4.5 MHz carrier modulated with fh = 15.743 kHz SIF level = 100 mVpp indication: STATUS Bit[6] standard BTSC stereo signal, sound carrier only fPilot Pilot Frequency Range ANA_IN1+ ANA_IN2+ 15.563 BTSC Characteristics (MSP Standard Code = 20hex, 21hex) with a minimum IF input signal level of 70 mVpp (measured without any video/chroma signal components) S/NBTSC S/N of BTSC Stereo Signal S/N of BTSC-SAP Signal DACp_s, SCn_OUT_s1) 64 55 dB dB 1 kHz L or R or SAP, 100% modulation, 75 s deemphasis, RMS unweighted 0 to 15 kHz 1 kHz L or R or SAP, 100% 75 s EIM2), DBX NR, RMS unweighted 0 to 15 kHz L or R or SAP, 1%...66% EIM2), DBX NR THDBTSC THD+N of BTSC Stereo Signal THD+N of BTSC SAP Signal 0.15 0.8 % % fRBTSC Frequency Response of BTSC Stereo, 50 Hz...12 kHz Frequency Response of BTSCSAP, 50 Hz...9 kHz -0.5 -1.0 0.5 0.6 dB dB XTALKBTSC Stereo SAP SAP Stereo 75 75 dB dB 1 kHz L or R or SAP, 100% modulation, 75 s deemphasis, Bandpass 1 kHz L or R 1%...66% EIM2), DBX NR SEPBTSC Stereo Separation 50 Hz...10 kHz 50 Hz...12 kHz 35 30 dB dB 1) 2) "n" means "1", "2", "3", or "4"; "s" means "L" or "R"; "p" means "M" or "A" EIM refers to 75-s Equivalent Input Modulation. It is defined as the audio-signal level which results in a stated percentage modulation, when the DBX encoding process is replaced by a 75-s preemphasis network. MICRONAS INTERMETALL 77 MSP 34x1G PRELIMINARY DATA SHEET Symbol Parameter Pin Name Min. Typ. Max. Unit Test Conditions EIA-J Characteristics (MSP Standard Code = 30hex) S/NEIAJ S/N of EIA-J Stereo Signal S/N of EIA-J Sub-Channel THDEIAJ THD+N of EIA-J Stereo Signal THD+N of EIA-J Sub-Channel fREIAJ Frequency Response of EIA-J Stereo, 50 Hz...12 kHz Frequency Response of EIA-J Sub-Channel, 50 Hz...12 kHz XTALKEIAJ Main SUB Sub MAIN SEPEIAJ Stereo Separation 50 Hz...5 kHz 50 Hz...10 kHz -0.5 -1.0 DACp_s, SCn_OUT_s1) 60 60 0.2 0.3 0.5 0.5 dB dB % % dB dB 100% modulation, 75 s deemphasis 1 kHz L or R, 100% modulation, 75 s deemphasis, RMS unweighted 0 to 15 kHz 66 80 dB dB 1 kHz L or R, 100% modulation, 75 s deemphasis, Bandpass 1 kHz EIA-J Stereo Signal, L or R 100% modulation 35 28 dB dB FM-Radio Characteristics (MSP Standard Code = 40hex) S/NUKW THDUKW fRUKW S/N of FM-Radio Stereo Signal THD+N of FM-Radio Stereo Signal Frequency Response of FM-Radio Stereo 50 Hz...15 kHz Stereo Separation 50 Hz...15 kHz Pilot Frequency Range ANA_IN1+ ANA_IN2+ DACp_s, SCn_OUT_s1) 68 0.1 dB % 1 kHz L or R, 100% modulation, 75 s deemphasis, RMS unweighted 0 to 15 kHz L or R, 1%...100% modulation, 75 s deemphasis dB dB 19.125 kHz standard FM radio stereo signal -1.0 45 18.844 +0.5 SEPUKW fPilot 1) "n" means "1", "2", "3", or "4"; "s" means "L" or "R"; "p" means "M" or "A" 78 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 5. Appendix A: Overview of TV-Sound Standards 5.1. NICAM 728 Table 5-1: Summary of NICAM 728 sound modulation parameters Specification Carrier frequency of digital sound Transmission rate Type of modulation Spectrum shaping Roll-off factor 1.0 Carrier frequency of analog sound component Power ratio between vision carrier and analog sound carrier Power ratio between analog and modulated digital sound carrier 6.0 MHz FM mono 10 dB 0.4 5.5 MHz FM mono 13 dB I 6.552 MHz B/G 5.85 MHz L 5.85 MHz 728 kbit/s Differentially encoded quadrature phase shift keying (DQPSK) by means of Roll-off filters 0.4 6.5 MHz AM mono terrestrial 10 dB cable 16 dB 13 dB 0.4 6.5 MHz FM mono D/K 5.85 MHz 10 dB 7 dB 17 dB 11 dB China/Hu ngary 12 dB Poland 7 dB Table 5-2: Summary of NICAM 728 sound coding characteristics Characteristics Audio sampling frequency Number of channels Initial resolution Companding characteristics Coding for compressed samples Preemphasis Audio overload level Values 32 kHz 2 14 bit/sample near instantaneous, with compression to 10 bits/sample in 32-samples (1 ms) blocks 2's complement CCITT Recommendation J.17 (6.5 dB attenuation at 800 Hz) +12 dBm measured at the unity gain frequency of the preemphasis network (2 kHz) MICRONAS INTERMETALL 79 MSP 34x1G 5.2. A2-Systems PRELIMINARY DATA SHEET Table 5-3: Key parameters for A2 Systems of Standards B/G, D/K, and M Characteristics TV-Sound Standard Carrier frequency in MHz B/G 5.5 Sound Carrier FM1 D/K 6.5 M 4.5 B/G 5.7421875 Sound Carrier FM2 D/K 6.2578125 6.7421875 5.7421875 20 dB 40 Hz to 15 kHz 50 s 27/50 kHz 75 s 17/25 kHz 50 s 27/50 kHz 75 s 15/25 kHz M 4.724212 Vision/sound power difference Sound bandwidth Preemphasis Frequency deviation (nom/max) Transmission Modes Mono transmission Stereo transmission Dual sound transmission Identification of Transmission Mode Pilot carrier frequency Max. deviation portion Type of modulation / modulation depth Modulation frequency (L+R)/2 13 dB mono (L+R)/2 R mono (L-R)/2 language B language A 54.6875 kHz 55.0699 kHz 2.5 kHz AM / 50% mono: unmodulated stereo: 117.5 Hz dual: 274.1 Hz 149.9 Hz 276.0 Hz 80 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 5.3. BTSC-Sound System Table 5-4: Key parameters for BTSC-Sound Systems Aural Carrier (L+R) Carrier frequency (fhNTSC = 15.734 kHz) (fhPAL = 15.625 kHz) Sound bandwidth in kHz Preemphasis Max. deviation to Aural Carrier Max. Freq. Deviation of Subcarrier Modulation Type 1) BTSC-MPX-Components Pilot fh (L-R) 2 fh SAP 5 fh Prof. Ch. 6.5 fh 4.5 MHz Baseband 0.05 - 15 75 s 73 kHz (total) 25 kHz1) 5 kHz 0.05 - 15 DBX 50 kHz1) 0.05 - 12 DBX 15 kHz 10 kHz FM 0.05 - 3.4 150 s 3 kHz 3 kHz FM AM Sum does not exceed 50 kHz due to interleaving effects 5.4. Japanese FM Stereo System (EIA-J) Table 5-5: Key parameters for Japanese FM-Stereo Sound System EIA-J Aural Carrier FM Carrier frequency (fh = 15.734 kHz) Sound bandwidth Preemphasis Max. deviation portion to Aural Carrier Max. Freq. Deviation of Subcarrier Modulation Type Transmitter-sided delay Mono transmission Stereo transmission Bilingual transmission 20 s L+R L+R Language A 47 kHz 4.5 MHz EIA-J-MPX-Components (L+R) Baseband 0.05 - 15 kHz 75 s 25 kHz (L-R) 2 fh 0.05 - 15 kHz 75 s 20 kHz 10 kHz FM 0 s - L-R Language B Identification 3.5 fh - none 2 kHz 60% AM 0 s unmodulated 982.5 Hz 922.5 Hz MICRONAS INTERMETALL 81 MSP 34x1G 5.5. FM Satellite Sound PRELIMINARY DATA SHEET Table 5-6: Key parameters for FM Satellite Sound Carrier Frequency 6.5 MHz 7.02/7.20 MHz 7.38/7.56 MHz 7.74/7.92 MHz Maximum FM Deviation 85 kHz 50 kHz 50 kHz 50 kHz Sound Mode Mono Mono/Stereo/Bilingual Mono/Stereo/Bilingual Mono/Stereo/Bilingual Bandwidth 15 kHz 15 kHz 15 kHz 15 kHz Deemphasis 50 s adaptive adaptive adaptive 5.6. FM-Stereo Radio Table 5-7: Key parameters for FM-Stereo Radio Systems Aural Carrier (L+R) Carrier frequency (fp = 19 kHz) Sound bandwidth in kHz Preemphasis: - USA - Europe Max. deviation to Aural Carrier 75 kHz (100%) 10.7 MHz Baseband 0.05 - 15 75 s 50 s 90% 10% FM-Radio-MPX-Components Pilot fp (L-R) 2 fp 0.05 - 15 75 s 50 s 90% 5% RDS/ARI 3 fh 82 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 6. Appendix B: Manual/Compatibility Mode To adapt the modes of the STANDARD SELECT register to individual requirements and for reasons of compatibility to the MSP 34x0D, the MSP 34x1G offers an Manual/Compatibility Mode, which provides sophisticated programming of the MSP 34x1G. Using the STANDARD SELECT register generally provides a more economic way to program the MSP 34x1G and will result in optimal behavior. Therefore, it is not recommended to use the Manual/Compatibility mode. Only in those cases, where compatibility with MSP 34x0D is strictly required, should the Manual/Compatibility mode be used. Note: In case of Automatic Sound Select (MODUS[0]=1), any modifications of the demodulator write registers listed below, except AUTO_FM/AM, are ignored. MICRONAS INTERMETALL 83 MSP 34x1G 6.1. Demodulator Write and Read Registers for Manual/Compatibility Mode PRELIMINARY DATA SHEET Table 6-1: Demodulator Write Registers; Subaddress: 10hex; these registers are not readable! Demodulator Write Registers AUTO_FM/AM Address (hex) 00 21 MSPVersion 3411, 34511) Description 1. MODUS[0]=1 (Automatic Sound Select): Switching Level threshold of Automatic Switching between NICAM and FM/AM in case of bad NICAM reception 2. MODUS[0]=0 (Manual Mode): Activation and configuration of Automatic Switching between NICAM and FM/AM in case of bad NICAM reception A2_Threshold CM_Threshold AD_CV MODE_REG 00 22 00 24 00 BB 00 83 all all all 3411, 34511) A2 Stereo Identification Threshold Carrier-Mute Threshold SIF-input selection, configuration of AGC, and Carrier-Mute Function Controlling of MSP-Demodulator and Interface options. As soon as this register is applied, the MSP 34x1G works in the MSP 34x0D Compatibility Mode. Warning: In this mode, BTSC, EIA-J, and FM-Radio are disabled. Only MSP 34x0D features are available; the use of MODUS and STATUS register is not allowed. The MSP 34x1G is reset to the normal mode by first programming the MODUS register followed by transmitting a valid standard code to the STANDARD SELECTION register. FIR1 FIR2 DCO1_LO DCO1_HI DCO2_LO DCO2_HI PLL_CAPS 1) Reset Mode 00 00 Page 86 00 19hex 00 2Ahex 00 00 00 00 87 87 88 89 00 01 00 05 00 93 00 9B 00 A3 00 AB 00 1F FIR1-filter coefficients channel 1 (6 8 bit) FIR2-filter coefficients channel 2 (6 8 bit), + 3 8 bit offset (total 72 bit) Increment channel 1 Low Part Increment channel 1 High Part Increment channel 2 Low Part Increment channel 2 High Part Not of interest for the customer Switchable PLL capacitors to tune open-loop frequency 00 00 00 00 91 91 00 56 94 not in BTSC, EIA-J, and FM-Radio mode Table 6-2: Demodulator Read Registers; Subaddress: 11hex; these registers are not writable! Demodulator Read Registers C_AD_BITS ADD_BITS CIB_BITS ERROR_RATE PLL_CAPS AGC_GAIN Address (hex) 00 23 00 38 00 3E 00 57 02 1F 02 1E MSPVersion 3411, 3451 Description NICAM-Sync bit, NICAM-C-Bits, and three LSBs of additional data bits NICAM: bit [10:3] of additional data bits NICAM: CIB1 and CIB2 control bits NICAM error rate, updated with 182 ms Not for customer use Not for customer use Page 93 93 93 94 94 94 84 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 6.2. DSP Write and Read Registers for Manual/Compatibility Mode Table 6-3: DSP-Write Registers; Subaddress: 12hex, all registers are readable as well Write Register Volume SCART1 channel: Ctrl. mode FM Fixed Deemphasis FM Adaptive Deemphasis Identification Mode FM DC Notch Volume SCART2 channel: Ctrl. mode 00 15 00 17 00 40 Address (hex) 00 07 00 0F Bits [7..0] [15..8] [7..0] [7..0] [7..0] [7..0] Operational Modes and Adjustable Range [Linear mode / logarithmic mode] [50 s, 75 s, OFF] [OFF, WP1] [B/G, M] [ON, OFF] [Linear mode / logarithmic mode] Reset Mode 00hex 50 s OFF B/G ON 00hex Page 95 95 95 96 96 95 Table 6-4: DSP Read Registers; Subaddress: 13hex, all registers are not writable Additional Read Registers Stereo detection register for A2 Stereo Systems DC level readout FM1/Ch2-L DC level readout FM2/Ch1-R Address (hex) 00 18 00 1B 00 1C Bits [15..8] [15..0] [15..0] Output Range [80hex ... 7Fhex] [8000hex ... 7FFFhex] [8000hex ... 7FFFhex] 8 bit two's complement 16 bit two's complement 16 bit two's complement Page 96 96 96 MICRONAS INTERMETALL 85 MSP 34x1G 6.3. Manual/Compatibility Mode: Description of Demodulator Write Registers 6.3.1. Automatic Switching between NICAM and Analog Sound In case of bad NICAM reception or loss of the NICAM-carrier, the MSP 34x1G offers an Automatic Switching (fall back) to the analog sound (FM/AMMono), without the necessity of the controller reading and evaluating any parameters. If a proper NICAM signal returns, switching back to this source is performed automatically as well. The feature evaluates the NICAM ERROR_RATE and switches, if necessary, all output channels which are assigned to the NICAM source, to the analog source, and vice versa. An appropriate hysteresis algorithm avoids oscillating effects (see Fig. 6-1). STATUS[9] and C_AD_BITS[11] (Addr: 0023 hex) provide information about the actual NICAM-FM/AM-status. PRELIMINARY DATA SHEET Individual configuration of the threshold can be done using Table 6-5, whereby the bits 0 and 11 of AUTO_FM are ignored. It is recommended to use the internal setting used by the standard selection. The optimum NICAM sound can be assigned to the MSP output channels by selecting one of the "Stereo or A/B", "Stereo or A", or "Stereo or B" source channels. 6.3.1.2. Function in Manual Mode If the manual mode (MODUS[0]=0) is required, the activation and configuration of the Automatic Switching feature has to be done as described in Table 6-5. Note, that the channel matrix of the corresponding output channels must be set according to the NICAM mode and need not to be changed in the FM/AM-fallback case. Example: Required threshold = 500: bits [10:1]=00 1111 1010 6.3.1.1. Function in Automatic Sound Select Mode Selected Sound The Automatic Sound Select feature (MODUS[0]=1) includes the procedure mentioned above. By default, the internal ERROR_RATE threshold is set to 700dec. i.e. : - NICAM analog Sound if ERROR_RATE > 700 - analog Sound NICAM if ERROR_RATE < 700/2 The ERROR_RATE value of 700 corresponds to a BER of approximately 5.46*10-3/s. NICAM analog Sound ERROR_RATE threshold/2 threshold Fig. 6-1: Hysteresis for Automatic Switching Table 6-5: Coding of Automatic NICAM/Analog Sound Switching; Reset Status: Mode 0 Mode 0 Description Compatible to MSP 3410B, i.e. automatic switching is disabled Automatic Switching with internal threshold (Default, if Automatic Sound Select is on) Automatic Switching with external threshold (Customizing of Automatic Sound Select) Forced analog mono mode, i.e. Automatic Switching is disabled (Customizing of Automatic Sound Select) AUTO_FM [11:0] Addr. = 00 21hex Bit Bits Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit [0] =0 [10:1] = 0 [11] = 0 [0] =1 [10:1] = 0 [11] = 0 [0] =1 [10:1] = 25..1000 = threshold/2 [11] =0 [0] =1 [10:1] = 0 [11] = 1 ERROR_RATEThreshold/dec none Source Select: Input at NICAM Path1) always NICAM; Mute in case of no NICAM available NICAM or FM/AM, depending on ERROR_RATE 1 700 2 set by customer; recommended range: 50...2000 none always FM/AM 3 1) In case of Automatic Sound Select (MODUS[0] = 1), the NICAM path may be assigned to "Stereo or A/B", "Stereo or A", or "Stereo or B" source channels (see Table 2-2 on page 12). In case of Automatic Sound Select (MODUS[0] = 1), bit [0] of AUTO_FM is ignored 86 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 6.3.2. A2 Threshold The threshold between Stereo/Bilingual and Mono Identification for the A2 Standard has been made programmable according to the user's preferences. An internal hysteresis ensures robustness and stability. Table 6-6: Write Register on I2C Subaddress 10hex : A2 Threshold Register Address THRESHOLDS 00 22hex (write) A2 THRESHOLD Register Defines threshold of all A2 and EIA_J standards for Stereo and Bilingual detection bit [11..0] 7F0hex ... 190hex ... 0A0hex bit [15..12] force Mono Identification default setting after reset minimum Threshold for stable detection must be set to 0 A2_THRESH Function Name recommended range : 0A0hex...3C0hex 6.3.3. Carrier-Mute Threshold The Carrier-Mute threshold has been made programmable according to the user's preferences. An internal hysteresis ensures stable behavior. Table 6-7: Write Register on I2C Subaddress 10hex : Carrier-Mute Threshold Register Address THRESHOLDS 00 24hex (write) Carrier-Mute THRESHOLD Register Defines threshold for the carrier mute feature bit [6..0] 00hex ... 2Ahex ... 7Fhex Carrier-Mute always ON (both channels muted) default setting after reset Carrier-Mute always OFF (both channels forced on) must be set to 0 CM_THRESH Function Name bit [15..7] recommended range : 14hex...50hex MICRONAS INTERMETALL 87 MSP 34x1G 6.3.4. Register AD_CV The use of this register is no longer recommended. Use it only in cases where compatibility to the MSP 34x0D is required. Using the STANDARD SELECTION register together with the MODUS register provides a more economic way to program the MSP 34x1G. Table 6-8: AD_CV Register; reset status: all bits are "0" AD_CV (00 BBhex) Bit [0] [1-6] Function not used Reference level in case of Automatic Gain Control = on (see Table 6-9). Constant gain factor when Automatic Gain Control = off (see Table 6-10). Determination of Automatic Gain or Constant Gain Selection of Sound IF source (identical to MODUS[8]) MSP-Carrier-Mute Feature 0 = constant gain 1 = automatic gain 0 = ANA_IN1+ 1 = ANA_IN2+ 0 = off: no mute 1 = on: mute as described in section 2.2.2. must be set to 0 Settings must be set to 0 PRELIMINARY DATA SHEET Automatic setting by STANDARD SELECT Register 2-8, 0A-60hex 0 101000 9 0 100011 [7] [8] [9] 1 X 1 1 X 0 [10-15] not used 0 0 X : not affected while choosing the TV sound standard by means of the STANDARD SELECT Register Table 6-9: Reference Values for Active AGC (AD_CV[7] = 1) Application Input Signal Contains AD_CV [6:1] Ref. Value AD_CV [6:1] in integer Range of Input Signal at pin ANA_IN1+ and ANA_IN2+ Terrestrial TV - FM Standards - NICAM/FM - NICAM/AM - NICAM only SAT ADR 1) 1 or 2 FM Carriers 1 FM and 1 NICAM Carrier 1 AM and 1 NICAM Carrier 1 NICAM Carrier only 1 or more FM Carriers FM and ADR carriers 101000 101000 100011 010100 100011 40 40 35 20 35 0.10 - 3 Vpp1) 0.10 - 3 Vpp1) 0.10 - 1.4 Vpp (recommended: 0.10 - 0.8 Vpp) 0.05 - 1.0 Vpp 0.10 - 3 Vpp1) see DRP 3510A data sheet For signals above 1.4 Vpp, the minimum gain of 3 dB is switched, and overflow of the A/D converter may result. Due to the robustness of the internal processing, the IC works up to and even more than 3 Vpp, if norm conditions of FM/NICAM or FM1/FM2 ratio are supposed. In this overflow case, a loss of FM-S/N ratio of about 10 dB may appear. 88 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 6-10: AD_CV parameters for Constant Input Gain (AD_CV[7]=0) Step 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1) AD_CV [6:1] Constant Gain 000000 000001 000010 000011 000100 000101 000110 000111 001000 001001 001010 001011 001100 001101 001110 001111 010000 010001 010010 010011 010100 Gain 3.00 dB 3.85 dB 4.70 dB 5.55 dB 6.40 dB 7.25 dB 8.10 dB 8.95 dB 9.80 dB 10.65 dB 11.50 dB 12.35 dB 13.20 dB 14.05 dB 14.90 dB 15.75 dB 16.60 dB 17.45 dB 18.30 dB 19.15 dB 20.00 dB Input Level at pin ANA_IN1+ and ANA_IN2+ maximum input level: 3 Vpp (FM) or 1 Vpp (NICAM)1) maximum input level: 0.14 Vpp For signals above 1.4 Vpp, the minimum gain of 3 dB is switched and overflow of the A/D converter may result. Due to the robustness of the internal processing, the IC works up to and even more than 3 Vpp, if norm conditions of FM/NICAM or FM1/FM2 ratio are supposed. In this overflow case, a loss of FM-S/N ratio of about 10 dB may appear. 6.3.5. Register MODE_REG Note: The use of this register is no longer recommended. It should be used only in cases where software compatibility to the MSP 34x0D is required. Using the STANDARD SELECTION register together with the MODUS register provides a more economic way to program the MSP 34x1G. As soon as this register is applied, the MSP 34x1G works in the MSP 34x0D Compatibility Mode. In this mode: BTSC, EIA-J, and FM-Radio are disabled. Only MSP 34x0D features are available; the use of MODUS and STATUS register is not allowed. The MSP 34x1G is reset to the normal mode by first programming the MODUS register, followed by transmitting a valid standard code to the STANDARD SELECTION register. The register `MODE_REG' contains the control bits determining the operation mode of the MSP 34x1G in the MSP 34x0D Compatibility Mode; Table 6-11 explains all bit positions. MICRONAS INTERMETALL 89 MSP 34x1G Table 6-11: Control word `MODE_REG'; reset status: all bits are "0" MODE_REG 00 83hex Bit [0] [1] [2] Function not used DCTR_TRI I2S_TRI Digital control out 0/1 tri-state I2S outputs tri-state (I2S_CL, I2S_WS, I2S_DA_OUT) Master/Slave mode of the I2S bus WS due to the Sony or Philips-Format Switch Audio_Clock_Output to tri-state Mode of MSP-Ch1 Comment Definition 0 : must be used 0 : active 1 : tri-state 0 : active 1 : tri-state 0 : Master 1 : Slave 0 : Sony 1 : Philips 0 : on 1 : tri-state 0 : FM 1 : Nicam 0 : must be used Mode of MSP-Ch2 High Deviation Mode (channel matrix must be sound A) 0 : FM 1 : AM 0 : normal 1 : high deviation mode 0 : must be used see also Table 6-13 see also Table 6-13 Mode of MSP-Ch1/ ADR-Interface Gain for AM Demodulation 0 : Gain = 6 dB 1 : Gain = 0 dB 0 : use FIR1 1 : use FIR2 0 : normal mode/tri-state 1 : ADR-mode/active 0 : 0 dB (default. of MSPB) 1 :12 dB (recommended) PRELIMINARY DATA SHEET Automatic setting by STANDARD SELECT Register 2-5 0 X X 8, A, B 0 X X 9 0 X X [3] [4] [5] I2S Mode1) I2S_WS Mode Audio_CL_OUT X X X X X X X X X [6] [7] [8] [9] NICAM1) not used FM AM HDEV 0 0 0 0 1 0 0 0 1 0 1 0 [11:10] [12] [13] [14] [15] not used MSP-Ch1 Gain FIR1-Filter Coeff. Set ADR AM-Gain 0 0 1 0 1 0 0 0 0 1 0 0 0 0 1 X: not affected by short-programming 90 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G The loading sequences must be obeyed. To change a coefficient set, the complete block FIR1 or FIR2 must be transmitted. Note: For compatibility with MSP 3410B, IMREG1 and IMREG2 have to be transmitted. The value for IMREG1 and IMREG2 is 004. Due to the partitioning to 8-bit units, the values 04hex, 40hex, and 00hex arise. 6.3.7. DCO-Registers Note: The use of this register is no longer recommended. It should be used only in cases where software-compatibility to the MSP 34x0D is required. Using the STANDARD SELECTION register together with the MODUS register provides a more economic way to program the MSP 34x1G. Value 04hex 40hex 00hex Table 6-12: Loading sequence for FIR-coefficients FIR1 00 01hex (MSP-Ch1: NICAM/FM2) No. 1 2 3 4 5 6 Symbol Name NICAM/FM2_Coeff. (5) NICAM/FM2_Coeff. (4) NICAM/FM2_Coeff. (3) NICAM/FM2_Coeff. (2) NICAM/FM2_Coeff. (1) NICAM/FM2_Coeff. (0) Bits 8 8 8 see Table 6-13 8 8 8 Value FIR2 00 05hex (MSP-Ch2: FM1/AM) No. 1 2 3 4 5 6 7 8 9 Symbol Name IMREG1 IMREG1/ IMREG2 IMREG2 FM/AM_Coef (5) FM/AM_Coef (4) FM/AM_Coef (3) FM/AM_Coef (2) FM/AM_Coef (1) FM/AM_Coef (0) Bits 8 8 8 8 8 8 see Table 6-13 8 8 8 When selecting a TV-sound standard by means of the STANDARD SELECT register, all frequency tuning is performed automatically. If manual setting of the tuning frequency is required, a set of 24-bit registers determining the mixing frequencies of the quadrature mixers can be written manually into the IC. In Table 6-14, some examples of DCO registers are listed. It is necessary to divide them up into low part and high part. The formula for the calculation of the registers for any chosen IF frequency is as follows: INCRdec = int(f/fs 224) with: int = integer function f = IF frequency in MHz fS = sampling frequency (18.432 MHz) Conversion of INCR into hex-format and separation of the 12-bit low and high parts lead to the required register values (DCO1_HI or _LO for MSP-Ch1, DCO2_HI or LO for MSP-Ch2). 6.3.6. FIR-Parameter, Registers FIR1 and FIR2 Note: The use of this register is no longer recommended. It should be used only in cases where software compatibility to the MSP 34x0D is required. Using the STANDARD SELECTION register together with the MODUS register provides a more economic way to program the MSP 34x1G. Data-shaping and/or FM/AM bandwidth limitation is performed by a pair of linear phase Finite Impulse Response filters (FIR-filter). The filter coefficients are programmable and are either configured automatically by the STANDARD SELECT register or written manually by the control processor via the control bus. Two not necessarily different sets of coefficients are required: one for MSP-Ch1 (NICAM or FM2) and one for MSP-Ch2 (FM1 = FM-mono). In Table 6-13 several coefficient sets are proposed. To load the FIR-filters, the following data values are to be transferred 8 bits at a time embedded LSB-bound in a 16-bit word. MICRONAS INTERMETALL 91 MSP 34x1G PRELIMINARY DATA SHEET Table 6-13: 8-bit FIR-coefficients (decimal integer); reset status: all coefficients are "0" Coefficients for FIR1 00 01hex and FIR2 00 05hex Terrestrial TV Standards FM - Satellite FIR filter corresponds to a band-pass with a bandwidth of B = 130 to 500 kHz B fc frequency B/G-, D/KNICAM-FM INICAM-FM FIR1 2 4 -6 -4 40 94 0 FIR2 3 18 27 48 66 72 LNICAM-AM FIR1 -2 -8 -10 10 50 86 0 FIR2 -4 -12 -9 23 79 126 B/G-, D/K-, M-Dual FM FIR2 3 18 27 48 66 72 0 130 kHz FIR2 73 53 64 119 101 127 1 180 kHz FIR2 9 18 28 47 55 64 1 200 kHz FIR2 3 18 27 48 66 72 1 280 kHz FIR2 -8 -8 4 36 78 107 1 380 kHz FIR2 -1 -9 -16 5 65 123 1 500 kHz FIR2 -1 -1 -8 2 59 126 1 Autosearch FIR2 -1 -1 -8 2 59 126 0 Coef(i) 0 1 2 3 4 5 ModeREG[12] ModeREG[13] FIR1 -2 -8 -10 10 50 86 0 FIR2 3 18 27 48 66 72 0 0 0 1 1 1 1 1 1 1 0 For compatibility, except for the FIR2-AM and the Autosearch-sets, the FIR-filter programming as used for the MSP 3410B is also possible. ADR coefficients are listed in the DRP data sheet. Table 6-14: DCO registers for the MSP 34x1G; reset status: DCO_HI/LO = "0000" DCO1_LO 00 93hex, DCO1_HI 00 9Bhex; DCO2_LO 00 A3hex, DCO2_HI 00 ABhex Freq. MHz 4.5 5.04 5.5 5.58 5.7421875 6.0 6.2 6.5 6.552 7.02 7.38 DCO_HI/hex 03E8 0460 04C6 04D8 04FC 0535 0561 05A4 05B0 0618 0668 DCO_LO/hex 000 0000 038E 0000 00AA 0555 0C71 071C 0000 0000 0000 5.76 5.85 5.94 6.6 6.65 6.8 7.2 7.56 0500 0514 0528 05BA 05C5 05E7 0640 0690 0000 0000 0000 0AAA 0C71 01C7 0000 0000 Freq. MHz DCO_HI/hex DCO_LO/hex 92 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 6-15: NICAM operation modes as defined by the EBU NICAM 728 specification C4 0 0 0 C3 0 0 0 0 0 0 0 C2 0 0 1 1 0 0 1 C1 0 1 0 1 0 1 0 Operation Mode Stereo sound (NICAMA/B), independent mono sound (FM1) Two independent mono signals (NICAMA, FM1) Three independent mono channels (NICAMA, NICAMB, FM1) Data transmission only; no audio Stereo sound (NICAMA/B), FM1 carries same channel One mono signal (NICAMA). FM1 carries same channel as NICAMA Two independent mono channels (NICAMA, NICAMB). FM1 carries same channel as NICAMA Data transmission only; no audio Unimplemented sound coding option (not yet defined by EBU NICAM 728 specification) 6.4. Manual/Compatibility Mode: Description of Demodulator Read Registers Note: The use of these register is no longer recommended. It should be used only in cases where software compatibility to the MSP 34x0D is required. Using the STANDARD SELECTION register together with the STATUS register provides a more economic way to program the MSP 34x1G and to retrieve information from the IC. All registers except C_AD_BITs are 8 bits wide. They can be read out of the RAM of the MSP 34x1G if the MSP 34x0D Compatibility Mode is required. All transmissions take place in 16-bit words. The valid 8-bit data are the 8 LSBs of the received data word. If the Automatic Sound Select feature is not used, the NICAM or FM-identification parameters must be read and evaluated by the controller in order to enable appropriate switching of the channel select matrix of the baseband processing part. The FM-identification registers are described in section 6.6.1. To handle the NICAM-sound and to observe the NICAM-quality, at least the registers C_AD_BITS and ERROR_RATE must be read and evaluated by the controller. Additional data bits and CIB bits, if supplied by the NICAM transmitter, can be obtained by reading the registers ADD_BITS and CIB_BITS. 0 1 1 1 1 x 0 1 1 x 1 x AUTO_FM: monitor bit for the AUTO_FM Status: 0: NICAM source is NICAM 1: NICAM source is FM 6.4.1. NICAM Mode Control/Additional Data Bits Register NICAM operation mode control bits and A[2:0] of the additional data bits. Format: MSB 11 Auto _FM ... ... 7 A[2] Note: It is no longer necessary to read out and evaluate the C_AD_BITS. All evaluation is performed in the MSP and indicated in the STATUS register. 6.4.2. Additional Data Bits Register Contains the remaining 8 of the 11 additional data bits. The additional data bits are not yet defined by the NICAM 728 system. Format: MSB 7 6 A[9] 5 A[8] C_AD_BITS 00 23hex 6 A[1] 5 A[0] 4 C4 3 C3 2 C2 1 C1 LSB 0 S ADD_BITS 00 38hex 4 A[7] 3 A[6] 2 A[5] 1 A[4] LSB 0 A[3] Important: "S" = Bit[0] indicates correct NICAM-synchronization (S = 1). If S = 0, the MSP 3411/3451G has not yet synchronized correctly to frame and sequence, or has lost synchronization. The remaining read registers are therefore not valid. The MSP mutes the NICAM output automatically and tries to synchronize again as long as MODE_REG[6] is set. The operation mode is coded by C4-C1 as shown in Table 6-15. A[10] 6.4.3. CIB Bits Register CIB bits 1 and 2 (see NICAM 728 specifications). Format: MSB 7 x 6 x 5 x CIB_BITS 00 3Ehex 4 x 3 x 2 x 1 CIB1 LSB 0 CIB2 MICRONAS INTERMETALL 93 MSP 34x1G 6.4.4. NICAM Error Rate Register ERROR_RATE Error free maximum error rate 00 57hex 0000hex 07FFhex PRELIMINARY DATA SHEET 6.4.7. Automatic Search Function for FM-Carrier Detection in Satellite Mode The AM demodulation ability of the MSP 34x1G offers the possibility to calculate the "field strength" of the momentarily selected FM carrier, which can be read out by the controller. In SAT receivers, this feature can be used to make automatic FM carrier search possible. For this, the MSP has to be switched to AM-mode (MODE_REG[8]), FM-Prescale must be set to 7Fhex = +127dec, and the FM DC notch (see section 6.5.7.) must be switched off. The sound-IF frequency range must now be "scanned" in the MSP-channel 2 by means of the programmable quadrature mixer with an appropriate incremental frequency (i.e. 10 kHz). After each incrementation, a field strength value is available at the quasi-peak detector output (quasipeak detector source must be set to FM), which must be examined for relative maxima by the controller. This results in either continuing search or switching the MSP back to FM demodulation mode. During the search process, the FIR2 must be loaded with the coefficient set "AUTOSEARCH", which enables small bandwidth, resulting in appropriate field strength characteristics. The absolute field strength value (can be read out of "quasi-peak detector output FM1") also gives information on whether a main FM carrier or a subcarrier was detected; and as a practical consequence, the FM bandwidth (FIR1/2) and the deemphasis (50 s or adaptive) can be switched accordingly. Due to the fact that a constant demodulation frequency offset of a few kHz leads to a DC level in the demodulated signal, further fine tuning of the found carrier can be achieved by evaluating the "DC Level Readout FM1". Therefore, the FM DC Notch must be switched on, and the demodulator part must be switched back to FM-demodulation mode. For a detailed description of the automatic search function, please refer to the corresponding MSP Windows software. Average error rate of the NICAM reception in a time interval of 182 ms, which should be close to 0. The initial and maximum value of ERROR_RATE is 2047. This value is also active if the NICAM bit of MODE_REG is not set. Since the value is achieved by filtering, a certain transition time (approx. 0.5 sec) is unavoidable. Acceptable audio may have error rates up to a value of 700 int. Individual evaluation of this value by the controller and an appropriate threshold may define the fallback mode from NICAM to FM/AM-Mono in case of poor NICAM reception. The bit error rate per second (BER) can be calculated by means of the following formula: BER = ERROR_RATE * 12.3*10-6 /s 6.4.5. PLL_CAPS Readback Register It is possible to read out the actual setting of the PLL_CAPS. In standard applications, this register is not of interest for the customer. PLL_CAPS minimum frequency nominal frequency maximum frequency PLL_CAPS PLL open PLL closed 02 1Fhex L 1111 1111 0101 0110 RESET 0000 0000 02 1Fhex H xxxx xxx0 xxxx xxx1 FFhex 56hex 00hex 6.4.6. AGC_GAIN Readback Register It is possible to read out the actual setting of AGC_GAIN in Automatic Gain Mode. In standard applications, this register is not of interest for the customer. AGC_GAIN max. amplification (20 dB) min. amplification (3 dB) 02 1Ehex 0001 0100 0000 0000 14hex 00hex 94 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 6.5.2. Volume Modes of SCART1/2 Outputs Volume Mode SCART1 Volume Mode SCART2 00 07hex 00 40hex 0000 RESET 0001 [3:0] [3:0] 0hex 1hex 6.5. Manual/Compatibility Mode: Description of DSP Write Registers 6.5.1. Additional Channel Matrix Modes Loudspeaker Matrix Headphone Matrix SCART1 Matrix SCART2 Matrix I2S Matrix Quasi-Peak Detector Matrix SUM/DIFF AB_XCHANGE PHASE_CHANGE_B PHASE_CHANGE_A A_ONLY B_ONLY 00 08hex 00 09hex 00 0Ahex 00 41hex 00 0Bhex 00 0Chex 0100 0000 0101 0000 0110 0000 0111 0000 1000 0000 1001 0000 L L L L linear logarithmic Linear Mode L Volume SCART1 L Volume SCART2 40hex 50hex 60hex 70hex 80hex 90hex OFF 0 dB gain (digital full scale (FS) to 2 VRMS output) +6 dB gain (-6 dBFS to 2 VRMS output) 00 40hex 0000 0000 RESET 0100 0000 H 00hex 40hex 00 07hex H 0111 1111 7Fhex This table shows additional modes for the channel matrix registers. The sum/difference mode can be used together with the quasi-peak detector to determine the sound material mode. If the difference signal on channel B (right) is near to zero, and the sum signal on channel A (left) is high, the incoming audio signal is mono. If there is a significant level on the difference signal, the incoming audio is stereo. Note: SCART Volume linear mode will not be supported in the future (documented for compatibility reasons only). 6.5.3. FM Fixed Deemphasis FM Deemphasis 50 s 75 s OFF 00 0Fhex 0000 0000 RESET 0000 0001 0011 1111 H 00hex 01hex 3Fhex 6.5.4. FM Adaptive Deemphasis FM Adaptive Deemphasis WP1 OFF WP1 00 0Fhex 0000 0000 RESET 0011 1111 L 00hex 3Fhex 6.5.5. NICAM Deemphasis A J17 Deemphasis is always applied to the NICAM signal. It is not switchable. MICRONAS INTERMETALL 95 MSP 34x1G 6.5.6. Identification Mode for A2 Stereo Systems Identification Mode Standard B/G (German Stereo) Standard M (Korean Stereo) Reset of Ident-Filter 00 15hex 0000 0000 RESET 0000 0001 0011 1111 L 00hex 01hex MONO 3Fhex STEREO Stereo Detection Register Stereo Mode PRELIMINARY DATA SHEET 6.6.1. Stereo Detection Register for A2 Stereo Systems 00 18hex H Reading (two's complement) near zero positive value (ideal reception: 7Fhex) negative value (ideal reception: 80hex) To shorten the response time of the identification algorithm after a program change between two FM-Stereo capable programs, the reset of the ident-filter can be applied. Sequence: 1. Program change 2. Reset ident-filter 3. Set identification mode back to standard B/G or M 4. Read stereo detection register BILINGUAL Note: It is no longer necessary to read out and evaluate the A2 identification level. All evaluation is performed in the MSP and indicated in the STATUS register. 6.6.2. DC Level Register DC Level Readout FM1 (MSP-Ch2) 00 1Bhex 00 1Chex H+L H+L 6.5.7. FM DC Notch The DC compensation filter (FM DC Notch) for FM input can be switched off. This is used to speed up the automatic search function (see Section 6.4.7.). In normal FM-mode, the FM DC Notch should be switched on. FM DC Notch ON OFF 00 17hex 0000 0000 Reset 0011 1111 L 00hex 3Fhex DC Level Readout FM2 (MSP-Ch1) DC Level [8000hex ... 7FFFhex] values are 16 bit two's complement The DC level register measures the DC component of the incoming FM signals (FM1 and FM2). This can be used for seek functions in satellite receivers and for IF FM frequencies fine tuning. A too low demodulation frequency (DCO) results in a positive DC-level and vice versa. For further processing, the DC content of the demodulated FM signals is suppressed. The time constant , defining the transition time of the DC Level Register, is approximately 28 ms. 6.6. Manual/Compatibility Mode: Description of DSP Read Registers All readable registers are 16-bit wide. Transmissions via I2C bus have to take place in 16-bit words. Some of the defined 16-bit words are divided into low and high byte, thus holding two different control entities. These registers are not writable. 6.7. Demodulator Source Channels in Manual Mode 6.7.1. Terrestric Sound Standards Table 6-16 shows the source channel assignment of the demodulated signals in case of manual mode for all terrestric sound standards. See Table 2-2 for the assignment in the Automatic Sound Select mode. In manual mode for terrestric sound standards, only two demodulator sources are defined. 6.7.2. SAT Sound Standards Table 6-17 shows the source channel assignment of the demodulated signals for SAT sound standards. 96 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G Table 6-16: Manual Sound Select Mode for Terrestric Sound Standards Source Channels of Sound Select Block Broadcasted Sound Standard B/G-FM D/K-FM M-Korea M-Japan Selected MSP Standard Code 03 04, 05 02 30 Broadcasted Sound Mode MONO STEREO BILINGUAL, Languages A and B B/G-NICAM L-NICAM I-NICAM D/K-NICAM D/K-NICAM (with high deviation FM) FM Matrix FM/AM (use 0 for channel select) Stereo or A/B (use 1 for channel select) Sound A Mono German Stereo Korean Stereo No Matrix Sound A Mono Mono Stereo Left = A Right = B analog Mono Mono Stereo Left = A Right = B no sound with AUTO_FM: analog Mono 08 09 0A 0B 0C NICAM not available or NICAM error rate too high MONO STEREO BILINGUAL, Languages A and B MONO Sound A Mono Sound A Mono Sound A Mono Sound A Mono Korean Stereo Sound A Mono Korean Stereo Sound A Mono analog Mono analog Mono analog Mono Mono Stereo Mono Stereo Mono NICAM Mono NICAM Stereo Left = NICAM A Right = NICAM B Mono Stereo Mono Stereo Mono 20 STEREO MONO + SAP STEREO + SAP MONO BTSC 21 STEREO MONO + SAP STEREO + SAP No Matrix Sound A Mono Korean Stereo Left = Mono Right = SAP Mono Stereo Left = Mono Right = SAP Mono Stereo FM-Radio 40 MONO STEREO Table 6-17: Manual Sound Select Modes for SAT-Modes (FM Matrix is set automatically) Source Channels of Sound Select Block for SAT-Modes Broadcasted Sound Standard Selected MSP Standard Code 6, 50hex FM SAT 51hex Broadcasted Sound Mode FM/AM (source select: 0) Stereo or A/B (source select: 1) Stereo or A (source select: 3) Stereo or B (source select: 4) MONO STEREO BILINGUAL Mono Stereo Left = A (FM1) Right = B (FM2) Mono Stereo Left = A (FM1) Right = B (FM2) Mono Stereo A (FM1) Mono Stereo B (FM2) MICRONAS INTERMETALL 97 MSP 34x1G 6.8. Exclusions of Audio Baseband Features In general, all functions can be switched independently. Two exceptions exist: 1. NICAM cannot be processed simultaneously with the FM2 channel. 2. FM adaptive deemphasis cannot be processed simultaneously with FM-identification. PRELIMINARY DATA SHEET 6.9. Phase Relationship of Analog Outputs The analog output signals: Loudspeaker, headphone, and SCART2 all have the same phases. The user does not need to correct output phases when using these analog outputs directly. The SCART1 output has opposite phase. Using the I2S-outputs for other DSPs or D/A converters, care must be taken to adjust for the correct phase. If the attached coprocessor is one of the MSP family, the following schematics help to determine the phase relationship. I2S_IN1/2 I2S_OUT1/2 Loudspeaker Headphone SCART1-Ch. Audio Baseband Processing SCART1 SCART2 SCART3 SCART4 MONO MONO, SCART1...4 SCART Output Select SCART DSP Input Select SCART1 SCART2-Ch. SCART2 Fig. 6-2: Phase diagram of the MSP 34x1G 98 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G 7. Appendix D: MSP 34x1G Version History MSP 3451G-A1 First release MSP 3451G-A2 - CONTROL register now readable for more status information - new D/K standard for Poland - improved I2C hardware problem handling - improved AM-performance MICRONAS INTERMETALL 99 MSP 34x1G 8. Appendix E: Application Circuit IF 2 IN if ANA_IN2+ not used PRELIMINARY DATA SHEET Tuner 2 Signal GND IF 1 IN 10 F + 3.3 F 56 pF 56 pF 56 pF + 100 nF 100 nF 18.432 MHz C s. section 4.6.2. 8 V(5 V) 100 pF 56 pF Tuner 1 ANA_IN1+ + 10 F + 10 F 1 K Alternative circuit for ANA_IN1+for more attenuation of video components: XTAL_IN (62) 21 ANA_IN- (59) 24 VREFTOP (54) 29 XTAL_OUT (63) 20 ANA_IN1+ (58) 25 ANA_IN2+ (60) 23 CAPL_M (40) 44 CAPL_A (38) 46 AGNDC (42) 42 1 F 1 F 1 F DACM_L (29) 56 330 nF 28 (55) MONO_IN 1 nF DACM_R (28) 57 330 nF 330 nF AHVSS 330 nF 330 nF AHVSS 330 nF 330 nF AHVSS 330 nF 38 (45) ASG4 40 (43) SC4_IN_L 39 (44) SC4_IN_R 31 (52) SC1_IN_L 1 nF 30 (53) SC1_IN_R 32 (51) ASG1 34 (49) SC2_IN_L 33 (50) SC2_IN_R 35 (48) ASG2 37 (46) SC3_IN_L 36 (47) SC3_IN_R DACA_R (25) 60 1 nF DACA_L (26) 59 1 nF 1 nF DACM_SUB (31) 54 LOUD SPEAKER 1 F 1 F HEAD PHONE 5V 5V DVSS 330 nF MSP 34x1G SC1_OUT_L (37) 47 SC1_OUT_R (36) 48 100 22 F + 11 (7) STANDBYQ 12 (6) ADR_SEL 100 22 F + DVSS 8 (10) I2C_DA 9 (9) I2C_CL 1 (16) ADR_WS 68 (17) ADR_CL 3 (15) ADR_DA 6 (12) I2S_WS 7 (11) I2S_CL 4 (14) I2S_DA_IN1 65 (20) I2S_DA_IN2 5 (13) I2S_DA_OUT 45 (39) AHVSUP 61 (24) RESETQ 67 (18) DVSUP 26 (57) AVSUP 66 (19) DVSS 27 (56) AVSS SC2_OUT_L (34) 50 100 22 F + SC2_OUT_R (33) 51 100 22 F + D_CTR_I/O_0 (5) 13 D_CTR_I/O_1 (4) 14 AUD_CL_OUT (1) 18 TESTEN (61) 22 43 (41) AHVSS 49 (35) VREF1 58 (27) VREF2 AHVSS RESETQ (from Controller, see section 4.6.3.3.) 220 pF 470 pF 1.5 nF 10 F 470 pF 1.5 nF 10 F 470 pF 1.5 nF 10 F Note: Pin numbers refer to the PLCC68 package, numbers in brackets refer to the PSDIP64 package. AHVSS AHVSS AHVSS 5V 5V AVSS 8V (5 V) 100 MICRONAS INTERMETALL PRELIMINARY DATA SHEET MSP 34x1G MICRONAS INTERMETALL 101 MSP 34x1G 9. Data Sheet History 1. Preliminary data sheet: "MSP 34x1G Multistandard Sound Processor Family with Virtual Dolby Surround", Edition Oct. 15, 1999, 6251-511-1PD. First release of the preliminary data sheet. PRELIMINARY DATA SHEET MICRONAS INTERMETALL GmbH Hans-Bunte-Strasse 19 D-79108 Freiburg (Germany) P.O. Box 840 D-79008 Freiburg (Germany) Tel. +49-761-517-0 Fax +49-761-517-2174 E-mail: docservice@intermetall.de Internet: http://www.intermetall.de Printed in Germany Order No. 6251-511-1PD All information and data contained in this data sheet is without any commitment, is not to be considered as an offer for conclusion of a contract nor shall it be construed as to create any liability. Any new issue of this data sheet invalidates previous issues. Product availability and delivery dates are exclusively subject to our respective order confirmation form; the same applies to orders based on development samples delivered. By this publication, MICRONAS INTERMETALL GmbH does not assume responsibility for patent infringements or other rights of third parties which may result from its use. Reprinting is generally permitted, indicating the source. However, our prior consent must be obtained in all cases. 102 MICRONAS INTERMETALL |
Price & Availability of MSP3B441G
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |